m18 claymore mine 3d models

However, if your tripod isn't very good (mine aren't) I'd suggest setting the camera to use electronic shutter and either remotely trigger it or use the selt timer -- that will minimize misalignments due to vibration -- and also brace the tripod...

I got mine from https://3dprintingcanada.com/collections/tpe/products/black-1-75mm-tpe-filament-0-5-kg (not affiliated). Video: - In action: https://youtu.be/3EBpf9YP5C4 - Showing the shock: https://youtu.be/YSYngEb9dG8 - Gearbox assembly:...

They can be mounted with stock components, or with another work of mine, the "anti Z wobble" inspired by HEVORT (I put the link at the bottom of the article). The attachments are fixed to the aluminum profile of the X axis with 4 M5 12mm screws and...

The Fan connector on mine actually would fit through sideways, and the Extruder Motor connector wouldn't quite fit, but I flexed the plastic and got it through. You also have the option of unscrewing these and reattaching them on the other side. I...

I went with a 32 microstep on mine setup and I know there is 1.7 gazillion for microstepping and 1.7 gazillion against it. I wanted quieter as this little printer rarely if ever see's the kind of stepper load where it runs out of torque and starts...

I didn't use a sealed tub for mine, and just sealed up the lid and other holes with weatherstripping tape. It has stayed quite well sealed, but naturally a proper sealed tub will work better and not require the extra sealing steps. The spool...

For a wiring diagram please refer to the images for how mine is setup as an example.   BOM 1x Battery Display : https://www.amazon.co.uk/dp/B07DVSTY59 4x M5 70mm Bolts : https://www.amazon.co.uk/dp/B07X8Q73SK 4x M5 Serrated Flange Nuts...

Mine are 25mm, for example, the Cross Country Performance kit uses 30mm thick spacers so you could modify the height in the Z-Axis in your slicer to potentially get 2.5" of lift from the tophat spacers alone. The lift given by the thickness of the...

I used the same for the rest of the system on mine.Total cost of this project using the required materials is less than $70 not including the print. The individual cost of these components is much lower if you buy them in multipacks. I've found that...

 This means using a bolt of 35 mm (M4 or M3 will do) for the pivot.By the way, to access the Dremel chuck clamp you can…A) loosen the M3 corner screw on the upper_pillar_clamp and turn the Dremel roundB) take the rubber bands off and drop the...

:) I included the modified STLs I used to make mine, basically smaller versions of DIY-Machines version and more of them and I added separate diffusers instead of his multi-filament versions, so that they can be printed on my smaller single-color 3D...

I didn't bother installing it for mine. Brass rather than steel is a good choice to avoid scratching your camera's mount surface.</p><figure class="image"><img...

I use a 5 minute 2-part epoxy from any hardware store (I get mine from Harbor Freight since its super cheap and works the same as any other brand). Start with gluing together the 2 middle pieces, ‘Middle Bottom’ and ‘Middle Top’. It's at this point...

- if there is a fit issue (I had to change the dimension thickness of the chassis) hot water bend these to fit but mine fit perfect Lower box and rod - No support needed - 20 minute print - free mount for the base of the box, the rod will connect to...

Mine had somehow drifted over time due to loose screws, because of which I wasted some time in understanding why my X carriage didn't move freely and was wobbling a bit. After meticulously squaring the frame, the problem was resolved. **Mandatory...

Connects to TFT (I have unplugged it from the TFT on mine, I always use Octoprint so I send the sensor interrupt to a Raspberry Pi). Outermost pin is pin 1 in my scheme. Lower side: * BLTouch signal connector. Labeled as S1 and S2 * 24-pin...

Tools you need: Torx T10or M2.5 Allen Key (for most of the M3 screws around the box) Torx T8or M2 Allen Key (for the side housing walls) Fine Tweezers Soldering iron (optional) 2.5mm JST crimp tool (optional) Parts you will need: 10x M3 nut 12x M3x12...

Obviously, you will also need to buy an electric cable including a connector (I bought mine at "Clas Ohlson" in Sweden). You must ENSURE not to overheat the printed parts so take good care of which lamps to use. Personally, I use LED lamps of...

Behind this is a small project of mine, in the course of which I want to cram as many sensors, actuators and breakboards for the Arduino into a housing as possible. Plus a 7 inch touch screen and lots of communication interfaces. Why? I might tell in...

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of an adjustable...

... chain for the gantry wires that lined up and worked well from that point. 12. Route your hotend wires back to your control module as you like. I've got connector plugs in mine near the gantry which is easy and also looks like hot garbage...

I've printed mine in extrudr GreenTec Pro silver (bearing-seat-cap_mount and drag-knife_mount) and extrudr PLA NX2 white (counter-ring).&nbsp;Post Print InstructionsInstall the bearing seat capInstall the threaded inserts in the...

The rig can be used for heavy mining operations in the future too! I added some inspiration pictures that really helped me to design this IMC gantry crane. Design is uploaded in IGES (its STEP now, while that did seem to work) for the final assembly...

…the corner pieces didn't print nicely enough for mine to perfectly assemble. (maybe that's my tuning issue, orientation, or lack of supports)--------------------everything below this line is copied from original that this is a remix of- full credit...

O-rings I got mine on Amazon as follows: 031 Silicone O-Ring, 70A Durometer, Red, 1-3/4" ID, 1-7/8" OD, 1/16" Width (Pack of 25) https://www.amazon.com/gp/product/B000FMYO6Y/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 023 Silicone O-Ring, 70A...

I printed mine in PLA with 7% infill, 2 perimeters, and 0.2 mm layer height. The filament I used was scavenged from a dumpster.</p><p><strong>Assembly Notes</strong></p><p>In general, there's only one way for pieces to fit together, so it should be...

Mine was like 2mm too short, so I had to get a couple of JST-XH female connectors and make a new, longer cable. SHIM The shim raises the whole extruder side of the solution up a bit, to be more in level with the hotend side. Also, some people...

Knob channel.stl - channel knob, for 16 position rotary encoder, model unknown, mine was from professional 16-ch radio. 7. Antenna.stl - old-style, PRR mock antenna. 8. Antenna New.stl - new style, EZ-PRR mock antenna. 9. PTT Lemo Single.stl - PTT...

This made mine work perfectly. Do this before placing the bearings in the bore, and do it with gloves on! The end mill caught me by surprise and drew blood.</p><h3>Print instructions</h3><p>I made the body in PETG, .2mm layer height, 3 perimeters,...

------------------------------------ ENGLISH ---------------------------------------------The guide was translated using google, I apologize in advance for any errorsTo conclude the set of linear guides on the X1, this time I propose some attachments...