m18 claymore mine 3d models

I use a jeweller's loupe to check the finish, but if you have better eyes than mine you might not need any magnificationIf you printed the reed tongues and blowpipe on a surface more rough than the Prusa smooth build sheet, you should sand their...

... gone well and you have a piece of furniture of which you can be justly proud.   I am certainly very happy with mine!There is a lot of documentation here, and I'd really appreciate any feedback on anything that's not clear or in need of correction.

I got mine from ebay. 8x22x7mm ABEC-5 608RS Skateboard Bearings (item number 392604796294) You need a suitable length of 4mm OD 2mm ID PTFE Bowden tube to connect the filament in the box to your extruder (any colour you like!). There are many sources...

One part of the railway was the coal (lignite) and briquette transport from nearby mines to the town to feed the steam engines mainly in cloth factories. There were about 70 of these wagons and trains could carry up to 15 to 20 wagons according the...

I think mine were roughly 9 inches/22 cm; longer is easier to work withCut a small length of aluminum wire and wrap around the center (this is just to hold everything together temporarilyCut another length of the black nylon thread, exact length...

I do appreciate Seth's support and input during this process, but the designs of the coins (and any failures thereof) are mine. No resale allowed but free sharing and further modification is encouraged.</p><p>These coins are intended to follow the...

I thought the frame came with this, but mine did not. * needs supports * 16% infill * **Vista_Antenna_Mount_FPVCycle_Fouride.stl** * Rear Vista antenna mount for the fouride. shorter in height than the one for the prototype this may...

Mine didn't came out great because of that, but yours can. - A printer that doesn't wobble/vibrate (tall structures may suffer from vibration, particularly the spine which needs to be somewhat straight and thin) ## Print orientations Case...

You may need to adjust the `centerColumnHeight` variable and re-build that object if your existing center column doesn't match mine. If you go this route, you'll need to lock the bottom reel to the 3D-printed central column, and lock each additional...

Mine just needed the supports to be removed and worked fine. To start, install the M3 nuts into the base, there are 10 pockets (see 1st pic) and I added a small drop of glue (clear Gorilla Glue) to each pocket, then pushed the M3 nut into the pocket...

Obviously, you will also need to buy an electric cable including a connector (I bought mine at "Clas Ohlson" in Sweden). You must ENSURE not to overheat the printed parts so take good care of which lamps to use. Personally, I use LED lamps of no more...

For example, mine had red, black, and green wires (which are used for 3.3v, ground, and signal respectively).Step 5Test the endstop with the board plugged into your Octoprint board. If the LED is ON before you insert the filament, the metal switch...

I used wood screws to mount mine. Any wood screws will work, just make sure they fit in the slotted holes so the plastic doesn't bust. You don't have to mount it yet, but partial disassembly will be needed to mount later. 12. Using 4 (1/2...

Obviously, you will also need to buy an electric cable including a connector (I bought mine at "Clas Ohlson" in Sweden). You must ENSURE not to overheat the printed parts so take good care of which lamps to use. Personally, I use LED lamps of...

... <h3>Final note</h3> <p>I would insulate the spring clips in the power track if there was any chance of shorts. Mine are mounted on wood. I haven't found a source for spring clips other than extracting them from a breadboard.

This is also an indication for printing these parts in an accent color (mine was orange).STL naming an meanings:[a]: accent color (means middle section of the pro version, mine was orange)x2: you have to print the part 2 times (example)IL1: parts for...

  If you cannot get the wire installed, STOP and investigate the print, since it should not take a great amount of force to install the wires, and you may have an issue with the print which is blocking the holes for the wire hinge.  Do not push too...

Dispensers for 12oz, and 16oz hold 3.5 cans per-layer plus 1.5 cans on the tongue.&nbsp;Printing and AssemblyLine&nbsp;I decided to slice mine with a 0.6mm line width even though I was printing with a 0.4 nozzle. so I could get a 1.2mm thick wall...

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-IBM-FA-3X150LED-RT is approved for use within environments where flammable or combustible...

They can be mounted with stock components, or with another work of mine, the "anti Z wobble" inspired by HEVORT (I put the link at the bottom of the article). The attachments are fixed to the aluminum profile of the X axis with 4 M5 12mm screws and 4...

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of two...

This is my Multi Material Upgrade (MMU) for the Printrbot Metal Plus inspired by the Prusa MMU. This collection of models has parts that I have remixed from: Josef Prusa (I used his MMU for a base to make mine) https://www.prusaprinters.org/...

And a 12 volt that moved an insane amount of air and sounded like a leaf blower. Print and assembly instructions I printed mine using PLA at .2mm. I really don't think it will matter much what you use as long as it can hold the screw threads.</p>...

Mine didn't came out great because of that, but yours can.A printer that doesn't wobble/vibrate (tall structures may suffer from vibration, particularly the spine which needs to be somewhat straight and thin)Print orientationsCase orientation: front...

&nbsp;I have mine in the front, with a USB fan in the back, but the opposite would also work fine. &nbsp;Which is best may depend on which direction you tend to feed filament. &nbsp;I don't hit any issues feeding filament under the bottom, past the...

I built a small cable like this for mine (you can see it at the back of the printer on the left in the pictures)I removed the stock LCD display as I don't use it with Klipper. You could potentially install it instead of one of the front right end...

Its fuel trailer and Inferno Gun gave the tank the name of flame thrower tank, clearing mine areas and making them safer for passage.The 3D printable Flamethrower Tank is showcased with its fearful gun in forward position. The model’s replica has all...

... if you get that far before I do and I'll update it here. Also, thanks to Tximy. Hole sizing and spacing from this design for the wheels/Eccentric nut saved me from having to fully dismantle mine. ... https://www.thingiverse.com/thing:3343882

I have mine configured for the wheels to roll along the X-axis & the carriage rolls along the 2040 V-Slot is the Y-axis. I wanted it that way for the X-axis to be the longest. I have my maximum X Position set to 1000mm. The wheel distance could be...

&nbsp;Try not to apply too much pressure, you don't need it, too much pressure might result in the cutter coming away from your straight edge.Things you need.60mm x 19mm x 0.6mm utility knife blade.3 x M3x16mm cap head screws.3 x M3...