m16 receiver 3d models

This Device Was Specifically Designed to Integrate a GPS Receiver, RF Link, Microcontroller, Batteries, and Charge Controllers. Following Printing, A Coating of Catla Paste Was Applied, Significantly Enhancing the Durability of PLA Materials and...

Just a small receiver box that will fit a standard rc receiver. Dimensions are5.9cm L x 3cm W x 3cm T without the lid. When put into my slicer I need to scale up to 1000% so double check your scale before printing. Supports are needed for the box...

Just a small receiver that will fit a standard rc receiver. Dimensions are5.9cm L x 3cm W x 3cm T without the lid. When put into my slicer I need to scale up to 1000% so double check your scale before printing. Supports are needed for the box because...

The paper cover around the receiver needs to be removed. Low tolerances. ###A lot of labor went into my designs. Designing, printing, testing, redesigning, retesting, .... I share my designs for free and love seeing people downloading them and using...

This is a simple receiver tray that allows for neat mounting of a receiver or gyro in the FMS Avanti EDF. The large holes on the sides are for the wires to come up through, and loop to the aft end of the RX. Small holes are for zip tie to tidy it up....

Waterproof Receivers Designed Specifically for Radio Controlled Vehicles and Robots Engineers Develop Impervious Electronic Receptacles for Demanding Environments Top-Rated Brands Now Offer Invasive Sealed Cases Perfect for Withstanding High-Tech Toy...

This innovative design combines three essential features: a sturdy wire antenna holder, which proved to be more resilient than T-antennas; a compact receiver housing that optimizes space beneath the canopy; and a LiPo pad that keeps screw heads...

For more information about the quad IR receiver module, refer to my blog post at http://teslaandi.wordpress.com/2014/01/26/quad-ir-receiver-module/. The circuit incorporates an AND gate that combines the outputs of four IR receiver modules for...

To make room for 4 cables (I2C + power) soldered to the bottom side of the CRSF-PWM-C board I have enlarged the housing by 1mm to the rear.The GY-63 is placed between CRSF-PWM-C and eLRS receiver board where is enough free space thanks to the...

Traxxas Rustler Receiver Box Unboxed and Ready to Roll Out Inside the Traxxas Rustler Receiver Box, you'll find a treasure trove of high-quality components that bring this rugged off-road truck to life. The first thing you'll notice is the sturdy...

This has always concerned me because tossing the Wii in my bag (I frequently take it to friends' houses) could damage the controller port or a part of the receiver from being jostled around in the bag. I wanted to create something that keeps the...

I was designing very specific Packout receiver to fit a toolbox and someone mentioned making a standalone universal receiver.  This receiver can be used in pairs to hang a full Packout box or standalone to hold items that only have one cleat.

You can check the Bluetooth receiver board here: https://www.parts-express.com/sure-electronics-aa-ab41136-bluetooth-40-audio-receiver-board-aptx--edr-12-vdc--320-351. I've been using this board for over three years, and I'm impressed with its sound...

This hitch receiver plug is designed for use with Class I and II receivers (1-1/4" x 1-1/4"). Initially, I conceived it with the intention that the cross would need to be painted on, but subsequently redesigned it so that the cross can be printed...

Measuring (excluding the USB port itself) 14.1mm x 6.4mm, my receiver performs flawlessly but may require some minor adjustments if your device is slightly larger. I've found it compatible with a couple of Logitech nano usb receivers, although...

I used to simply attach the receiver PCB with 3M UHB tape, but I recently ran into a situation where I needed to remove the electronics from a model to perform some repairs. The tape did its job too well and I decided to re-mount the Rx so it could...

I designed this Xbox Wireless receiver holder for my PC because I was fed up with it constantly falling off my desk and disappearing on me. I added a clip at the front of the receiver holder so that I could easily locate it after using the USB port...

Additional to the flightcontroller you need an RC-receiver that works with your transmitter. You don't need a lot of range so use a old or a crappy one. To protect this devices i've designed a box. Betaflight CLI command: set usb_hid_cdc =...

Here are the essential components I employed: The Monitor A generic 5.8GHz FPV Receiver This mount should seamlessly integrate with other models as well. To complete the setup, you will also need a versatile 1/4" to 3/8" Convert Screw Adapter for...

To keep the receiver dry and clean, protect it from dirt like sand. It's not completely waterproof, but if you seal it with the same grease or silicone rubber, I think it will be waterproof. Just close all the holes that maybe water can go into the...

This is a unique opportunity for the Falcon Receiver.\r\n\r\nThere are two distinct options available for the base, one that perfectly aligns with the holes on a CG1500 box and another option without the tabs specifically designed for the CG...

This compact piece replaces the spacer situated beneath the top rail in the handguard, and fits snugly into a small hex-shaped hole in the receiver during assembly, preventing the handguard from rotating inadvertently and loosening the barrel nut. ...To...

The product can be found on Aliexpress at the following URL:...

I got tired trying to keep all the wiring from getting into the servos and creating a tangled mess in my Dynam Primo RC Plane, so I came up with this clever solution - a tray that holds the receiver above the servos and protects them from all the...

The paper cover around the receiver needs to be removed. Low tolerances. ###A lot of labor went into my designs. Designing, printing, testing, redesigning, retesting, .... I share my designs for free and love seeing people downloading them and...

3 different RC Receiver mounts for Spektrum AR410, AR630 and AR631.The 410 has very little clearance and can slip loose on a hard landing, but it does not support ASX and SAFE, so this should not impact flight. Velcro tends to allow the receiver...

The components that the support is tailored to are: Receiver: FrSky X-Mini or FrSky R-XSR VTX: AKK for stacking Barometer: BMP280 To secure the VTx, I employed the standard nylon nuts with M3 screws. ... (Note: This output has a Flesch-Kincaid grade...

Receiver mount for 220 frame quadcopter.. connects underneath top plate to standoffs over the FC. For 3mm antenna tubes sold at hobbytown USA. ...This design clears the props and is under the top plate between camera and FC, which is a little extra...

A simple solution involves crafting an airfoil-shaped fairing specifically designed to house FRsky receiver antennas. To assemble this protective covering, merely punch a small hole through it and make a slight incision. Next, carefully insert the...

You can purchase a simple DCF77 clock receiver, which is an European atomic clock, on eBay for a few euros. ...The goal is to attach the 4 wires directly to an Arduino chip, and there's a library that makes it easy to read out the signal:...