m10 5883 3d models
5428 3d models found related to m10 5883.
thingiverse
NOT TESTED YET attempt for AOS7 INAV gps mount for Matek m10-5883 (32x32x10)
thingiverse
I needed an antenna and GPS mount for the AOS UL5, and thought I'd share it. ... This is for the O3 Antenna and the Matek M10-5883 GPS. ... Printed in TPU w/ 50% infill it came out under 5g
thingiverse
SMA and gps mount for the RAD Li-ion 7" long range frame. ... I like to print this with 4 walls to help and keep it stiff to avoid vibrations from the antennas.
thingiverse
Mount for 10mm diameter caps and the GPS Matek M10 5883 11/03/2023 Edit: -Added a version for a 16mm dimater Caps and Fettec Spike Absorvers
thingiverse
Remixed for matek 743 wing v3, matek gnss M10-5883
thingiverse
***FIT'S ALMOST ANY FRAME WITH 5mm STANDOFFS*** Exact fit for Matek M8Q-5883/M10Q-5883 with recessed edges for a secured fit. ... For best results, print right side up with normal supports.
thingiverse
Matek M8Q-5883 mount TPU ====== NEW ====== 2019/07/20 : M8Q-5883 v1.stl for Martian II 220mm frame with a 0-degree angle M8Q-5883 v2.stl for Martian II 220mm frame with a 25-degree tilt
grabcad
this is a Rough mockup (submillimeter accurate calipers used) of the M100-5883 HGLRC GPS. ...i use this model to cut out exact shapes of my Gps for perfect fits.
thingiverse
A straightforward enclosure for the Matek M8Q-5883 GPS/Compass module. To print this holder, use TPU material with a high infill percentage (I chose 70%). A snug fit is guaranteed, so be prepared to carefully maneuver the cover into place. ...I employed...
thingiverse
This is a simple protective case for the M10Q-5883 GPS module from Mateksys. I fill the bottom with hot glue to secure and help with vibration. The lid will screw on. ...I used a white filament at 20% infill to allow the LED light to pass through
thingiverse
Matek M9N-5883 Mount for FPV Drone frames with 15-25 mm distance between standoffs. Tested with iFlight Chimera7 and XL / SL series frames. ... Mount may fit Crossfire T-antenna and HGLRC Buzzer with LED INAV settings: set align_mag_yaw = 2700 ...
grabcad
Robot of the FRC 5883 Spice Gears team for the 2022 Rapid React competition.
thingiverse
A simple holder to mount the a GPS like Mateksys M8Q-5883 at the back of an iFlight Nazgul5 V2.
grabcad
... as a 'parafuso sextavado' in Portuguese. ...This M10-sized fastener features a hexagonal recess, designed for use with a six-pointed socket wrench or a similar tool, offering increased torque and better control during installation or removal processes.
thingiverse
Matek M8Q 5883 simple holder. Glue module with hot glue and glue holder with superglue on airplane framework. ...In case of polystyrol airplane, gps will work through polystryrol.
thingiverse
A straightforward application of the Matek M8Q-5883 GPS and compass module involves connecting it to a compatible flight controller and configuring its settings through the companion software.
thingiverse
Just a little GPS holder for the matek M8Q-5883 gps unit so you can easily mount it to a GPS Stalk
thingiverse
Here's a rewritten version of your text: Support for the Matek M8Q-5883 GPS module is available with an added RX antenna and a Crossfire antenna. ...The height of this setup is approximately 58 millimeters, while the center-to-center distance of the...
thingiverse
Designed specifically to complement the Matek M8Q-5883 GPS/Compass, this remix offers expanded functionality. Additionally, it features a unique mounting system underneath for an SMA connector and a designated spot up front to secure a capacitor.
thingiverse
Frontal GPS mount for the Matek M8Q-5883 for the MicroLongRange frame. Placing the GPS here will reduce noise and magnetic interference to a minimum. It will also not induce propeller disturbance compared to placement at the tail (where mounts will...