luigi 3d model

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Any sagging of overhangs that occur at the very top/front of the model can simply be trimmed or cleaned away after. The mount can be either just press fit (if tight enough) or glued in place into the holes on the back of the body. I recommend gluing...

All necessary supports are pre-applied to the models (there is no need to add additional supports). The main body of the stein/mug prints with cylindrical supports, the left/right lid have perforated supports, the lid top doesn't require supports...

Post-Printing // model: Prusa i3 MK3 Y Chassis Bearing Straps // This replaces the zip ties that tend to stretch and can reduce accuracy over time. Optionally, also replace the entire strap and bearing with a 1-piece printed version that has been...

After studying what was available, I started modeling my own. The problem was that most of the projects were on console tables, but our table is held on two rails, one on each side. Initially, the project was implemented on a seven-string polispast,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

I used this here: https://de.banggood.com/Remo-B5509-Ball-Bearings-593mm-For-1621-1625-1631-1635-1651-1655-RC-Vehicle-Models-p-1450586.html - 9x M3 30mm screws and nuts to conetc top and bottom trays - otionally: 9x M3 0.5mm washers to put between...

Found a simple hip flask just laying about USHip flask discovered seemingly abandoned USHip flask uncovered, left behind USHip flask in basic design chanced upon USHip flask, a basic model, was stumbled upon USHip flask, plainly designed, was located...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 6 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

Unfortunately, do not have access to a Prusa printer all the time, so testing will take a little while ---- Let's make this work together!;Because I can only test 1 day every 1 or 2 weeks on a Prusa printer, you can help me design this knob and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

I have not included the CAD model: As a newbie, I made a fair mess of things whilst modding along and fear that the kind people of Autodesk would take away my Fusion hobby license:)That's it!DOWNLOAD NOW for limited access to the crack attachment:) A...

Tree Supports and possibly Outer Brim required for some STLs NOTE: The STL Models may display some artifacts from revision builds, but will not appear in Print RECOMMEND: Allow pieces to cool to room temperature on printers Heatbed before removing to...

This would not work on a single nozzle printer, so we opted for truncated tetrahedra with slight insets on two of their triangular faces. INSTRUCTIONS Everything prints at 0.2 mm layer height.Set your line width to 0.45 mm, as the pattern...

Make sure you select your arduino model and com port. Extract the files There is a marlin.ino in there that you should select Then upload to your Ramps board and it should work, I'll test the sd card and lcd when I get the bits. I would definitely...

Use at your own risk!!Check out the current version of this design here. This design is tested and ready for use, but only uses one blower, not two.</strong></p><h3>Basics</h3><p>This design stemmed from my desire to create a perfectly controlled and...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

Different sizes and materials will result in orbs with different focal distances, which may mean you have to adjust the model for yours. Print it strong-- thick walls are a must. You'd be surprised how heavy the orb is. Also, I had to "floss" the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Use for reference) Hardware needed: Two 5015 blowers (get the correct voltage for your printer model). I recommend Sunon maglev. Europe: https://www.tme.eu/gb/details/mf50151vx-a99/dc12v-fans/sunon/mf50151vx-b00u-a99/. A suitable connector to the...

The color thicknesses and the width of the outline stripes on this test print match the stripes on this case and future cases I upload will probably use similar...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

... list of Remixes. If I have missed something please advise me and I will correct this ASAP. If you do not want your Thing as part of this collection please advise me and I will remove it and try to include an alternate Thing for the missing model.

I am keenly interested in optimizing this concept so that it Works for those needing a good, quality, multi-purpose coral frag plug so please leave comments on how I might improve this Thing. Instructions Additional fragging tools that might be of...

Furthermore I created the endstop mounts which are already present in the Fusion 360 model. I will try to update the pictures today or tomorrow. Now it gets exiting! Electronics are next! **Update 9** (03.07.2018): After test driving the Z-Axis I...

The hole for the cable tip should be wide enough for any similar cables, but if not you can pretty easily remix the model by just cutting the hole to be larger or adding material where needed. I suggest printing the dock upside down and including...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

For that reason, the drawers shown here have been modeled by means of [OpenJSCAD](https://openjscad.xyz/dokuwiki/doku.php), which give you the possibility to adjust them just by changing a few numbers and [rerun the script in your...