lucious models

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

I like you.text10 = ---textsizes = [13,13,13,13,8,8,8,10,6,10]Boat labeltext1 = Coast Guard Capacity Informationtext2 = ---text3 = Maximum persons|3text4 = Maximum gross load|100kgtext5 = Persons, motor & equip.|50 poundstext6 = Maximum...

I added a switch at the bottom of the right arm (super easy access).Please note, this system is designed to be mounted on an aluminum profile with a total width of 300mmPrints without support!Here you will find the links to the creations that have...

**Update 2022/04/08:** Fixed a bug in main body model. It was slightly to long on left bottom side to fit nicely over the antminer case. This project aims to convert a Bitcoin miner into a handy space heater. **We achieve this by:** *...

Deck furniture is always a good way to add interest to a model. You might want to install a waterproof switch somewhere on the exterior to save having to unscrew the whole deck every time to turn it off and on. Enjoy sailing your Pocket Boat,...

Verify the axle turns freely. Source File FreeCAD: BearingPegV4_2019.FCSTD Reinforced Within the pegs (excluding the original V4) 'pins' are embedded that promotes a strong cross pattern with lines at the stress point in addition to beveling....

To aide in designing this part, I also ordered a complete Neo hotend assembly from Amazon so I could 3d model all of the parts. Unfortunately, the back plate is not available to buy, but I was able to download an stl file from another Thingverse...

Video can be found here: https://youtu.be/41UrzTPhG0g STL and Editable Fusion 360 source files can be found here: https://bbprojects.technology/collections/stl-fusion-360-source-files/products/spacex-inspired-edf-rocket-model In the beginning of this...

Min of 190mm build volume Full print parts head on over to cults: https://cults3d.com/en/3d-model/various/scx6-trailer Can be setup as single or dual wheel. Dual wheel requires a min of 190mm. ** UPDATED parts ** 2022/02/10 - S Hook - to be...

Filament Dry Box (Peli Case) Storetwo standard 200mm filament spools in an air-tight Peli Case. Perfecting for storing your hygroscopic filaments after drying. The Dry box can be configured to simply store the filament, or by drilling and tapping 4 x...

 READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?This is my fifth...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

But don't hesitate to choose the one you prefer.The Raspberry Pi racks I designed are compatible with the Raspberry Pi 2B, 3B, 3B+ and now with the 4B models.I also added a rack version that doesn't use the snap&lock system ("Rack_RPi3&4_S"),...

I have not modeled any nut traps in the parts because I think they will weaken them so all bolts here just screw into the plastic. I believe the parts are thick enough that the bolts will not loosen but time will tell._ 1. Completely disassemble...

As provided the enclosure is set up to accept a 9.7" 2048x1536 panel as used by some iPads - Model No: LP097QX1-SPC1 https://it.aliexpress.com/item/1005002113658592.html There is no reason why you couldn't use any alternate panel and suitable driver...

... all STEP files are added for whoever wants to remix/adjust to there liking. Since I always tend to get frustrated by only having STL files of models that I want to improve/adjust I want to save you the pain of this and enable you to be creative :-).

There seem to be quite some error margin in production, if your model is a bit too big to fit, just sand off maybe .5 mm from the sides to make it fit.Completely(!) remove any filament remains inside the two enclosure parts.Fit servo into upper half...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

print the uppers in a 100% infill! Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...

If you want to use the hardware I intended this to use: Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge) Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

 When you slice the model for your printer, check a few crucial layers to make sure that the bolt holes and nut slots leave enough wall thickness everywhere.A note about the coordinate system:  The enclosure is modelled on it's left side,...

--- # Assembly ## Key Switch The key switch is a two-terminal model (aka, it only has "on" and "off" modes for simplicity) intended for generic Chinese electric scooter ignition. It is intended for a through-hole of ~10mm. I made it 11mm to account...

If there’s a flat-ish STL model that you like, you can load both this and that stl into Cura, scale and move them around as needed, and slice: Cura automatically joins models where they overlap. There’s also an insert plate that fits inside style0,...

... The single-blade model can be reversed in most slicer programs to cut from one side or the other of the 120 film, as described earlier, in "Preparing This Tool." The OpenSCAD source file therefore lacks any provision to make this adjustment. ...

If there is too little filament on the coil, it is pointless to print a large model. And it's a pity to throw away the leftovers, too. But you can print such a trinket as a gift or just for your own pleasure. P.S. When printing this model, not a...

However, for the non-threaded parts of your models there is no need to waste time and energy printing that fine (and slow). In the example below the use of variable layer height saves about 9 hours of printing time (which equals about 1.4 kWh of...

Adjust the bed leveling screw closest to where it measures and by the time the script has looped three times the bed will be perfectly level.Copy to your USB and just print it like you would a normal model (print the correct...

You may not be able to fit 3D printed indicator-mirror holder perfectly between brake lever and different shifter model.Ningbo Jietong Electronics • E751 (MIRS-201)2 x Amber color LED for left and right turn indicators.These switches are more...

Enable the "Generate Support" setting **PrusaSlicer** Load the model as a multi-part object into PrusaSlicer. Then perform the following actions, as in the screenshot: 1. Set the supports to Support Enforcers Only 2. Right click on the rectangle...