ltt logo 3d models

This is a LTT logo cube

Linus Tech Tips (LTT) logo keychain.

I also wanted to add the logo... for no practical reason This has been printed with PLA+, with 20% supports and infill. Slice it upside down, so that the flat top and bottom are at the top of your prints. ... A bit of sanding is needed to make the...

I took the LTT logo from a fan grill (https://www.thingiverse.com/thing:3587283) and flattened the bottom, then I took the wall mount (https://www.thingiverse.com/thing:5769352) and made a groove to glue the Logo onto it. (I did it this way so that I...

LTT Logo coaster made in Fusan 360

Added the LTT logo, as well as a little cutout on the left side to help make opening a little bit easier. ... Will likely add a model for the bit holder that has holes inlayed in the print for magnets to help hold onto the bits and prevent them...

... contrast to the original/remixed stand, this stand is supposed to be mounted to a wall or similar. The Case sits tighter in the socket. ...And has obviously a LTT logo.I butchered the mesh, but got it watertight.

Just a simple LTT Screwdriver pegboard mount/holder thingy.

This just holds it vertically and it fits inside an angled hole that helps hold it vertical and keeps it from falling over.I've created a version with and without the logo as well, but why would you use the one without?I printed these at 0.2mm with a...

1x1 Gridfinity holder for the LTT screwdriver. ...Created using the startpart from Zach Freedman.

This just holds it vertically and it fits inside an angled hole that helps hold it vertical and keeps it from falling over.I've created a version with and without the logo as well, but why would you use the one without?I printed these at 0.2mm with a...

A holder for mounting the LTT screwdriver under a desk or other surface. ...Would probably work for other drivers but the angle is mostly designed to balance the LTT driver

This is a simple pegboard mount for the LTT Screwdriver. ... It works on a pegboard with 1" spacing

I designed a holder to keep my LTT Screwdriver upright on my desk so it is easily at hand and quick to grab.

A simple foot sized for the 40oz LTT water bottle. ...I printed it in TPU and stuck it to the bottom with glue, to give it a more quite and softer base than the raw metal.

A wall mount for the ltt screwdriver so you can show it off while not using it.Best printed on with SLA printer but FDM works fine.Screws used 8.8mm x 2mm head, 4mm thread diameter.

LTT screwdriver does not ship with a case so i combined the screwdriver and bit trays by BonzNumber123 (https://www.thingiverse.com/thing:5733106) and the frog box. Because I essentially smashed together two STL's there is dimensional inaccuracies...

Edit it online https://www.tinkercad.com/things/kByfjsOJJV1 Modified version of [this print](https://www.printables.com/model/321009-ltt-screwdriver-skadis-hanger) for regular pegboards, unsure if pegboards use standardized measurements so your...

This lid was designed to replace the lid on the LTT water bottle so it can be used with one hand. ...Like with anything 3D printed you need to know your material and what it can handle so this is probably not recommended to use with hot beverages like...

This is a case for the LTT Screwdriver and 32 bits. I recommend using a bit of foam for the lid and the screwdriver. You will need to attach the two halves of the base and the two halves of the lid. Waiting to receive my screwdriver to make a plastic...

https://youtu.be/4Mt39qAgaoM This lid was designed to replace the lid on the LTT water bottle so it can be used with one hand. ...Like with anything 3D printed you need to know your material and what it can handle so this is probably not recommended to...

Introducing the unofficial 3D-printed LTT screwdriver clone, equipped with a removable ratchet mechanism and storage for six bits. Assembly is simple, with potential for minor adjustments using glue if needed. Ongoing enhancements ensure a robust yet...

This is to allow the choice of using standard bits because the bits from the LTT screwdriver are shorter than standard bits. Feel free to leave any questions or tips for improvements. I am still trying to work on a better version for the bit...

The LTT Screwdriver allows you to store up to 12x20mm bits in the handle, but there is no real storage solution for the additional bit sets other than leaving them in their little cardboard sleeves. This tray allows you to store up to 6 sets worth of...

Gridfinity, 6x2 for LTT Screwdriver plus 72 bits. If requested, I can upload one without the bitholders. I Used the cut tool in Pusaslicer and then glued the two halves together (Ø5mm, 5mm long) . Update 05-15-2024 - Added several STLS with differing...

I wanted a box to hold all the LTT bits I got with the screwdriver, and wanted to have TPU holders, kind of like the older iFixit tool kits. I didn't see anything already posted, so I made this. I built it to hold all the bits they offer (72), but...

If you don't have a 3D printer and what to buy one from me, here's a link to my Etsy store:...

In the most up-to-date versions of both the old nonmagnetic as well as this new magnetic version, the bits are held in place by bit holders that have an upward taper to allow for the plastic to deform and hold securely the bits without the use of...

This my version of a modular bit holder for the LTT Screwdriver. I have the screwdriver with me in my backpack and I like carrying all the bits "just in case". My main issue with other boxes and bit holders is that I WILL forget them somewhere,...