lt1 gen 2 3d models

POORLY SCANNED LT1 HEADSORRY ABOUT THE WEIRD BUNNY

POORLY SCANNED LT1 HEADSORRY ABOUT THE WEIRD BUNNY

There are 2 versions available. Ballistic and energetic. Floats. The turret and case have cutouts for 4mmx1mm magnets. In the future, the list of modifications will be replenished. ... More...

A mounting bracket for Onstep V4 Pro controller from Terrans Industry (also available on Aliexpress) designed to fit on a SkyWatcher EQ3-2 mount (specifically the LT1 aluminum tripod version).Before mounting the bracket on the tripod first attach it...

Toyota Sequoia 2 gen Scale Model •1:8•1:10•1:12•1:18•1:24•1:25•1:35•1:43•

I really enjoyed the first version of keychains for Gen 1 pokemon starters so I decided to do my own version with Gen 2. ...Keychains include a circle added on for the keychain caribiner, you have to add a negative part under the expert tab to the size...

I've Revamped the Gen 2 Pokémon Ornaments Simulator, Inspired by My Earlier Pokeball Ornament Masterpiece. So Far, It Includes: * Friend Ball * Lure Ball * Level Ball * Heavy Ball The Bottom Half, Part 1, is a Fundamental Component Used in All...

Made a version for Fossil gen 2 smartwatches with a handy cable channel. The stand itself is a bit wider than the original to be able to fit the charger. Printed on Ender 3 pro with standard settings for PLA in Cura. ...I used 20% infill with cubic...

This is the gen 2 Pokemon ornaments I have created simulator to the Pokeball ornament gen 1 I made some time ago https://www.thingiverse.com/thing:2719836 . so far includes Friend ball lure ball level ball heavy ball part 2 is the bottom half used in...

The cutest water starter from Gen 2! ...:P let's just say it that way ;) For Resin or FDM, needs minimal supports If you would like to get early releases and lower prices on Print files, or want to sell printed products, please subscribe to my Patreon...

I've created a gen 2 Pokémon ornament simulator, building on my previous Pokeball ornament from last year. You can check out the original design here: https://www.thingiverse.com/thing:2719836. So far, I've included ornaments for Friend Ball, Lure...

Generation 2 of my Ghosty Keychain

Chainblade(Or Ripper) arms for Generation 2 Includes - 10 Weapon arms (5 Right hands, 5 Left hands) - 6 Bare arms (3 Right hands, 3 Left hands) - 4 Dualing arms (2 Weapon arms, 2 Bare arms) - 2 Chainblades without hand (for Right hand & Left hand)...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: pulley_b_ht = 15.5, idler_ht = 3, idler = 2, m3_nut_flats = 10.4, pulley_b_dia = 25, m3_nut_depth = 5.1, motor_shaft = 8, retainer_ht = 3,...

Galileo Gen 2 Intel Human

Reflector for the Sofirn BLF LT1 lantern. ...I used duct tape for the reflective surface.

Apple airpods 2 gen. ...dock stand

Amazon Echo Dot Gen.2 Holder

Amazon echo (GEN 2) mount

There are two versions available: v1: My original idea, but my printer struggled with the 60° overhang at 0.2 mm layer height. v2: Slightly different design with a maximum overhang of 50° which worked fine. Initially I designed a complex mount with...

This is a simple base for the Sofirn LT1 lantern. It expands the base to approximately 4 inches to help reduce tipping. You'll need a 1/4x20 screw (1/2 inch long) and a hex nut. Inset the hex nut from above, tighten the screw from below, and then...

In my tests, an inner diameter of 35.75 was very loose, so you can increase the scale to 100.2% or 100.4% if it is too tight for you. I printed mine with a white glow-in-the-dark base layer and then switched to black. ...The design is public on...

BLF LT1 lantern as a reference for you mods and accessories. Outside dimensions are as accurate as I could measure them. ... Category: Models

A simple base for the BLF/Sofirn LT1 lantern. ...The cutout in the bottom is for a ring of rubber or foam.

BLF LT1 lantern as a reference for you mods and accessories. ...Outside dimensions are as accurate as I could measure them.

There are two versions available: v1: My original idea, but my printer struggled with the 60° overhang at 0.2 mm layer height. v2: Slightly different design with a maximum overhang of 50° which worked fine. Initially I designed a complex mount...

A basic stand for holding the Airpods Gen 2 case.

3D printed cup holder for gen 2 tacomas

This is the shade I designed for the BLF LT1 Lantern. I print it in PETG at 0.16mm on my Ender 3 v2 I print with a RAFT for best success. ...

... even more. Credits to Big_Sam for the original idea and first prototype. I've modeled this based on his photos and my [LT1 reference model](https://www.thingiverse.com/thing:4714912) and simplified it for easier printing and more robustness.