lrs 350 24 meanwell 3d models

Simple adapter to attach Meanwell LRS-350 PSU (at least revision 2019 Edward) to Ender 2 Pro.Pros:Button and plug are from the same side as the originalEasy to printDoesn't require disassembly of EnderEasy to mount and unmountCons:Sits not firmly due...

This is a custom enclosure designed to shield the Meanwell LRS-350 power supply from electrical shocks. Two openings allow for easy connection of power and on/off switch cables. Cable outlets are further protected by a rubber seal, guaranteeing a...

I'm combining [Kotze101's PSU cover](https://www.thingiverse.com/thing:2237395) with my [custom back cover](https://www.thingiverse.com/thing:2840001) on my Meanwell LRS-350-12, and the brackets stick out to accommodate the size of the back cover. I...

I found a good handful of Meanwell cases here, but none of them were exactly what I wanted, so I pulled the STLs from mlynch002's (very strong) Ender 3 Power Supply Relocation Bracket, and prudell's (very sleek & sexy) Mean Well LRS-350-24 PSU...

Noctua NF-A9-14 90mm fan cover for Meanwell PSU. Although intermittent, the stock fan on the Meanwell LRS 350W is loud when running. Switching it out for a 90mm noctua fan significantly reduced the fan noise.</p> <p>I've reduced the hex mesh from the...

The first is a stackable lid or hat for the Meanwell LRS-350 power supply, mine is the 5V version but I think they're all the same body. It gives you a few cm of clearance from the power supply so it can ventilate heat well enough, and gives you a...

This is a custom clamp designed specifically for securing a Meanwell LRS-350 power supply unit (PSU) to 2040 aluminum extrusions. To install the clamp, you will need two M4 screws with a diameter of 8mm, which will be used to attach the clamp...

... you need to ground the PSU - knock yourself out and run another wire for this ground connection. The Meanwell 350-24 has provisions for sufficient fault handling and isolation without it - I cannot speak for the other PSUs Creality uses. ...

The first is a stackable lid or hat for the Meanwell LRS-350 power supply, mine is the 5V version but I think they're all the same body. It gives you a few cm of clearance from the power supply so it can ventilate heat well enough, and gives you a...

It seemed like the power supply was glitching out on my Anycubic i3 Mega S, so I ended up replacing it with the MeanWell LRS-350. I used the power supply cover from Zcubed, the first picture one, and made a mount that makes this thing fit within...

It seemed like the power supply was glitching out on my Anycubic i3 Mega S, so I ended up replacing it with the MeanWell LRS-350. I used the power supply cover from Zcubed, the first picture one, and made a mount that makes this thing fit within...

It bounced right into one of the PSU slits I was using as a bench power supply (plucked from my PrusaMK3 after upgrading to LRS-350). Why not get another LRS350-24 since it fits my needs perfectly? I stumbled upon this PS design with a hinged cover...

why i did this remix (only thing changed on original files is a notch, but im not the original source, so i will not claim it as such) While recapping my Amiga1200 i foolishly let go of the strand of solder and would you guess, it bounced right into...

This addition makes LRS-350 fit snugly under the heated bed. I installed a power supply using this: https://www.senukai.lt/p/kampas-medinems-konstrukcijoms-tvirtinti-40x40x40x2-0-mm-vagner-sdh/2u8i Then I designed the box for the power socket and...

I upgraded my stock Ender 3 power supply after it failed multiple times, replacing it with the Meanwell power supply from the Ender 3 Pro and taking advantage of the opportunity to reposition the switch to the back of the printer. As seen in...

The stock Ender 3 power supply's failed several times on me, so i changed it to the Meanwell power supply from the Ender 3 Pro and took the chance to also relocate the switch to the back of the printer.As maybe seen in 'Thingiview' or in your Slicer,...

These enclosures were engineered to hold two Meanwell power supplies stacked vertically, one atop the other. ...A modified design features a slight offset to facilitate adjustment of the set screws on the lower supply when installed.

Holder for a Meanwell 48V power supply for powering Unifi switches for a mini server rack. ... Includes a cutout for a rocker on/off switch, such as: https://www.amazon.com/gp/product/B00OK901GK/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1

Safely stack the Meanwell Power supplies.This was originally created to stack power supplies in a CG1500 box.The addition of a terminal cover to help prevent fingers or objects accidentally touching live terminals (does not account for stupidity...

Enclosed Terminal for Safety Reasoning: Mean Well LRS-350-12 & LRS-350-24

Remix to fit the LRS 600-24 Meanwell PSU for Ender 3 V2, using the same fan as original design.

Mounting bracket LEFT and RIGHT for two Meanwell LRS200 or LRS350 Power Supply.Use M5 Bolts, Flat and Lock Washers.Print flat with large section on bed.I also design a similar kit for power supplies with dissimilar width (LRS200 or 350 at the bottom,...

Mounting bracket LEFT and RIGHT for two dissimilar width (LRS200 or 350 at the bottom, LRS-600 on top) power supplies.Use M5 Bolts, Flat and Lock Washers.Print flat with large section on bed.I also design a similar kit for two LRS200 or LRS350...

Rear frame mount for the MeanWell LRS-150-24 PowerSupply to a standard extrusion frame. &nbsp;Fusion 360 file for those that want to make further mods. ...&nbsp;If you want to put it on the Left Side, instead of the Right, just mirror it in...

It's a straightforward matter, just slap on some decent layers of filament and it'll likely do the trick. For best results, use either ABS or PETG – they're your safest bets. ...If you really want to push the limits with PLA, go ahead, but I'm not...

Fast casing for 24v Mean Well LRS 350-24. ... single part case.

I made this design to easy click on a cover for my powersupply.

This model does not precisely match the rail blocks that i used, but it was useful for general size/alignment purposes. MeanWell LRS model: Thanks to Chris for this one. The models don't <em>quite</em> match the PSUs that I got, but the model was...

Meanwell LRS-350-12 Power Supply Cover with Fan Cover for 92mm x 25mm Fan My fan was 12v I used a be quiet! ...Pure Wings 2 92mm, BL045 PS is silent now.