lrs 150 12 3d models

This is a DIN rail mounting bracket for the Meanwell LRS 350 power supply that uses the 4mm mounting holes on the back of the power supply. This mounts the power supply horizontally if your DIN rails are horizontal. STLs with and without beveled...

A cover for the Mean Well LRS 350. A fantastic power supply, except that the fan noise is brutal. The top cover has holes for the AC cable and three DC jacks, one for each of the outputs of the power supply. ...The cover is designed to be mounted to a...

This remix reimagines the frame-mount for the LRS-350, tailored to fit vertically under a table.\r\n\r\nTwo versions of the backplate are available: one is designed to stand alone, while the other is engineered to work in conjunction with the cover,...

The side of the original was too thick to slide into my LRS-350-48 so here is the modified version. ...The top has also increased 1.7mm so that it should shorten the gap that you see in my photo.

I needed a stand for my LRS-75 power supply with an arduino nano support for my diy ambilight system. Therefore I remixed the great stand from @IzK666 (https://www.thingiverse.com/thing:4897097) and merged it with an arduino case from @tjbn...

The side of the original was too thick to slide into my LRS-350-48 so here is the modified version. The top has also increased 1.7mm so that it should shorten the gap that you see in my photo. ... Category: 3D Printer Accessories

I wanted to protect my fingers from the mains on my power supply and wanted to use the Power Plug that I already had.Covers the mains cables on a Meanwell LRS 350 24V power...

A simple desk enclosure for the well known RIDEN RD60xx range of DC-DC power supply controllers AND a Meanwell LRS-100 power supplyGoogle the power receptable https://www.google.com/search?q=IEC+320+C14+male+panel+mountGoogle Riden power...

Case to secure a Mean Well LRS 200 to a wall or cabinet with a Digi Uno sticking out the top to expose a AE+ module so the touch interface, IR, and microphone are exposed. Not perfect but pretty good for a day of work. ...Feel free to fork and...

This adapter securely fastens a Falcon 4 port receiver to a Meanwell LRS power supply. To ensure a tight fit, drill out the three holes for the receiver and tap them with a 6/32 thread, then secure it using three 6/32 nylon machine screws. ...Next,...

[Japanese] 使わなくなった古い3Dプリンター（QIDI-TECH X-SMART）から取り出したMeanwell LRS-350-24をSOVOL SV06に移設するため、マウンターを作りました。ネジは全て標準の電源と同じものを再利用できます（Meanwell電源の方が薄いので1つ余ります）。配線位置も標準の電源と同じです。 SV06の標準電源は常にファンが全開で回っていましたが、Meanwell...

This model does not precisely match the rail blocks that i used, but it was useful for general size/alignment purposes. MeanWell LRS model: Thanks to Chris for this one. The models don't <em>quite</em> match the PSUs that I got, but the model was...

The case now fits the MEANWELL LRS-350 PSU perfectly, measuring in at a dimension of 115x30x215 mm. The front panel has been upgraded with a C14 socket featuring an accompanying switch available on AliExpress here:...

To find a suitable fit, I opted for a MeanWell LRS-350-24. The online designs available didn't quite meet my expectations, so I created a custom one that perfectly suits my needs. ...This design ensures the new PSU sits snugly against the printer frame,...

I remixed this so that it puts the back of the Meanwell LRS up against the wall of the ammo can, and the fan facing in towards the middle. I printed the original design, and it was reverse of what I wanted. Remixed it with tinkercad. I used M4 x...

As such I designed this mount for the LRS-350-24 PSU to fit my needs. ...It uses m4*8mm cap head screws to secure to the PSU, m3 cap head screws and lock nuts to secure the mains voltage socket, and m5*10mm screws and t-nuts to secure against the...

AboutA mounting cover for the Meanwell LRS-15-5 PSU; which not only gives additional protection (safety/insulation) but also allow easier mounting to a surface.No brims, or supports needed - just print! ...Printed with Prusament...

This is a sleek 3030 mount designed specifically for the Meanwell LRS-350 power supply - minimal design at its finest. Easy and fast to print, making it a joy for any DIY enthusiast. ... To bring this project to life, you'll need four M4x10 screws to...

Remix of the awesome LRS cover for the Prusa Mk3(s) to suit my needs i added a hole for the generic IEC connector found here: https://nl.aliexpress.com/item/32798405330.html?spm=a2g0s.9042311.0.0.27424c4dPv4WoK Full credit goes to original creator.

I designed this PSU cover for the Mean Well LRS-200 Power supply. It should be used in combo with a C14 Triple Outlet Socket 10A. The pilars in the model are build in support which come loos very easily. BOM: 220V/110V C14 Power Switch with Fuse...

Qty 2 M3 heat set inserts are used to mount the socket, I used McMaster Part # 94180A331.More information for 3D printing and 3D printable files can be found here:https://www.thingiverse.com/thing:6068969Credit to the following users for their models...

Table 150

Chair 150

Cessna 150

Screw 150

I replaced my default power supply with the meanwell LRS 350, but the new unit left a gap that needed to be closed. I didn't want to reprint the entire shroud, so I came up with this spacer solution. The spacer screws into the hole where the old...

When I replaced my default power supply with the meanwell LRS 350, the holder for the power supply had a gap that needed filling. I didn't want to re-print the whole shroud, so this spacer screws into the hole that the old power supply used. I put a...

This is a Mean Well LRS-350 power supply. It's based on the one-body model from "Chris" which I cut up and re-assembled with multiple bodies and components. I then made extensive revisions based on photos, measurements and OEM specifications. I'll...

I swapped out my Creality Ender-3's stock PSU for a Meanwell LRS-350-24, matching up mounting holes perfectly. A suitable cover proved elusive, so I took matters into my own hands and designed this one myself. You may need to bend the terminals or...

When I replaced my default power supply with the meanwell LRS 350, the holder for the power supply had a gap that needed filling. I didn't want to re-print the whole shroud, so this spacer screws into the hole that the old power supply used. I put a...