lowrider model

This is a DXF drawing for a plate suitable to mount the australian (bunnings brand) ozito ltm-3000 trim router into the lowrider2

This clips on the vertical pipes and holds the low rider near maximum height even after the steppers are disabled. You can scale Z height to make it hold at any height you want. ... Category: DIY

This is my remake of the belt tension system to fit over over cheap linear rails from Amazon. You can use 2 M6 Bolt/Nuts to tighten it up over the linear rail. Print upside down for the best results. The belt shouldn't rub up against the z pipes. ...

<p>Complete instructions can be found at the V1 Engineering Forum, following<a href="https://forum.v1engineering.com/t/how-to-build-611-y-flat-plates-with-almost-no-tools/29617"> THIS LINK.</a></p>

<p>**Update - 2019-08-02 - Added another version without the guides since I use grooves mounted in my table to keep the wheels accurate and don't need them anymore. Also has bumpers for endstops to contact (see my other project for endstop mounts).

Fusion 360 design file Mesh file See image for installation Bolt on with the Z motors sames screws. ...

Struggling to find FDM printable wheels for my scale projects I decided to make some that are printable on my Ender 3 Pro. The wheels can easily be made wider by increasing the width of the tire and loop. The rim faces are designed to be wide and...

Case to hold the power brick that I bought from V1engineering.com

Please look at pictures. ...Scalable in any size.

This is a custom-designed low-rider spacer specifically created for the ZMR250 frame, featuring ample side space to accommodate an array of essential electronic components, including the VTX transmitter. The innovative design allows for seamless...

A precision-crafted assembly combines a Session and Runcam Micro Swift FPV camera front section, along with an antenna tube mount system, specifically engineered for seamless integration with 10mm standoffs on the Anunnaki frame to achieve...

**Update - 2019-08-02 - Added another version without the guides since I use grooves mounted in my table to keep the wheels accurate and don't need them anymore. Also has bumpers for endstops to contact (see my other project for endstop mounts). ...

The original mounting components on the Quick Grab Phone Stand are being redesigned. This change allows for the removal of the long gantry, resulting in a narrower and more stable footprint that is less prone to vibration. This updated design...

A newer version of this machine is now available here, https://www.thingiverse.com/thing:3026040. All the parts are ready for assembly. The instructions are currently being worked on. This full sheet capable (4'x8') cnc router was inspired by the...

The revised version integrates minor components, streamlining the assembly process. The updated ZIP file includes all necessary files; special thanks to http://www.thingiverse.com/Starno for bringing this to our attention (previously downloaded 39...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/e9RfNJW6U0i

***Updated:*** One person's circuit board was a little too snug in the bottom hole where the solder points extend, so I widened that hole a bit to account for variances. I also added a small fillet to the holes, which matches the style of the part...

<p>I remixed this to fit this style of Endstops:<br/> <a...

Case and lisd for a Duet 2 Wifi to fit onto a LowRider3 CNC, or anything else you have a ¼" or less lip that you can hang the case from. It has room for both the built-in PCB antenna or a small hole suitable for the separate external antenna. ...(I've...

<p>This Clip will secure a standard shopvac hose to the Y-Plate of the LowRider2 CNC.<br><br>These are printed in PLA, but I suspect that anything will do!</p><p>For more information please visit the V1<a href="https://www.v1engineering.com">...

This is designed specifically for the MPCNC Lowrider2 CNC utilizing 2.54mm (1") tubing. These supports serve as a bridge between two pieces of tubing, providing structural support for an enclosure housing both the LCD display and control board. Two...

I Repaired a Faulty Sony Camera Mount that Rotates 15 Degrees, Adding an Underneath Protective Plate to Safeguard the Lens. ... Print Settings are as Follows: Rafts: Not Needed Supports: Yes, They Are Essential for Stability Resolution: I Opted for...

Replaces the original hopper adapter, and allows use of generic hoppers, also lowers the height. One piece press fits into the other, after installing the screws. Unfortunately removal is difficult to to screws being hidden after installation,...

The New Y-Belt System Upgrade for the Lowrider2 CNC.\r\nKey Features:\r\n - Quick and Accurate Setup Made Easy.\r\n - Belt Tension Adjusted with a Single Hand Tool in Minutes.\r\n - Optional Adjustable Bumper for Perfect Square Alignment on the...

My take on the Low Mod for Martian 2. Inspired by: https://www.thingiverse.com/thing:2577387 Full canopy with extra lip/trim/bumper for bottom plate. Full canopy without extra lip/trim/bumper for bottom plate. Front only with separate rear parts,...

I recently constructed this setup using sturdy Linear rails, but I quickly realized a major issue - no matter how tightly you secure them, they tend to slide out of place. To prevent this, I recommend implementing an additional locking mechanism to...

Adapter to connect X axis motor mount (Thing 3611502) to cable chain (Thing 611593 * 150 %) Bolt to stepper motor with M3 bolts and nuts. ...Bolt to cable chain with M5 bolts +/- nuts

I've got a 0.6mm nozzle on my printer that can't quite produce the fine teeth required to mesh perfectly with the belt. I really like the look of a GT2 belt that loops back onto itself - it's a sleek design that works in tandem with the original...

This clip attaches firmly to the upright pipes, securing the low rider at its highest point, even when the step motors are deactivated. ...By adjusting the Z-axis, you can easily fine-tune the holding height to suit your needs.