low poly werewolf 3d models

I tested multiple leaf-spring dimensions, and these seem pretty stable while having relatively low impact on operation smoothness.It needs some force to assemble it, so be careful. The hexagonal holes must be aligned with the two spring...

This is a followup to: Lack Attack#3: Koppla the Lack: https://www.prusaprinters.org/prints/15919-lack-attack-3-koppla-the-lack-aka-power-the-lack-s without further adieu.... Attack 4: ENCLOSE THE LACK Its been a while since my last update, mostly as...

Instead, 3 steel balls connected to the bed sit on low friction dowel pins. The pins act like a pair of rails for the steel balls, guiding their movement as the bed expands and ensuring that only radial movement is possible - there's zero margin for...

Try to find a low RPM motor rated for higher voltage (6V/12V). The typical 1.5/3v ones spin too fast with too little torque to work well with this design, and may overheat and burn.<ul><li>For a good quality option, the Mabuchi FK-130SH has carbon...

(Some of this is likely fixed by tuning to the correct printer settings, but you may be here regardless.) If they come out too snug, the issue is probably on the outer post's inside - sand that, keep fitting it, and work it until it's smooth but not...

at least two) parts (which, of course, have to be glued after printing) as visible in this section view of the same object:Reason is that, as detailed below, the threads should always be printed in a very high resolution (low layer height) while for...

On one of the two lower enclosures in my 2x2 stack, I mounted the spool holder low enough that the door of the enclosure above could swing over it, but I mounted the other one a bit too high. Rather than remove and remount it (possibly leaving a...

I've attached a picture of this, but basically the holes should be drilled as low as possible without reaching the point on the steel where it starts to curve. It should also be vertically aligned with the original screw holes. Once you've done this,...

None of the 10 boards I have managed to produce a stable 20 volts supply under even minor load.I drilled out the hold and mounted a simple socket for a laptop power supply.The back-panel will be redesigned for this.Print SettingsPrinter...

It has two additional holes that are intended to hold a small low-power toggle or push-button switch and an LED. How you wire those is entirely up to you (I used it as a cutoff switch for some extra layer fans, with the LED wired to light up when the...

Anyway you are advised, this can be even cheaper than those 2CH radios but full of possibilities :) I have been taking a look to some existing projects in the web about RC Control with Arduino and I think they reached the point of offering quite good...

Instead, 3 steel balls connected to the bed sit on low friction dowel pins. The pins act like a pair of rails for the steel balls, guiding their movement as the bed expands and ensuring that only radial movement is possible - there's zero margin for...

The parts are made to fit to it only.)1x ESP32 micro controller board (No ESP8266 use possible because of its low specs.)1x USB power supply 5V / >=3A1x Micro USB cable 3m  Printing instructions:No supports or brim needed for all parts.0.3 draft...

I guess you could print at a low enough temp that it gets a matte finish, but then I'd worry that the print wasn't strong enough. PLA or ABS would probably be less shiny, so fewer reflections (if you leave the foam screen out when installing...

Lock 26_ge_lock_7S(x11) needs to be printed 11 times; lock 27_ge_lock_10H(x12) needs to be printed 12 times;- All parts are divided in such a way that you will print them with the smallest number of support structures.DLP/SLA 1.0 version features:-...

The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 38 parts;- A printed model is 340 mm tall, 468 mm wide, 334 mm deep;-...

The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 33 parts;- A printed model is 556 mm tall, 290 mm wide, 342 mm...

The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.VERSION SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 24 parts;- A printed model is 280 mm tall, 164 mm wide, 164 mm deep;- Assembly...

The 3D printing figurine's chosen scale is 1/3 for the FFF/FDM version and 1/6 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 13 parts;- A printed model is 270 mm tall, 285 mm wide, 228 mm deep;- Assembly...

One lock 20_ge_lock_10H(x13)​ needs to be printed 13 times;- Made with a platform to resemble the coliseum area of Oolacile Township;- All parts are divided in such a way that you will print them with the smallest number of support structures.DLP/SLA...

One lock 27_ge_lock_7S(x1) needs to be printed once; lock 28_ge_lock_10H(x12) needs to be printed 12 times;- Comes with two variants of hand to fit either rifle or flamethrower;- Made with a platform to recreate the winter chapter of The Last of...

One lock 13_GeLock Small needs to be printed twice;- Made with a platform to resemble the Battle of Earth movie scene; - All parts are divided in such a way that you will print them with the smallest number of support structures.DLP/SLA 1.0 version...

One lock 31_ge_lock_7S(x1) needs to be printed once; lock 32_ge_lock_10H(x8) needs to be printed 8 times;- Made with a platform to recreate the nature of 16th century Sengoku Japan;- All parts are divided in such a way that you will print them with...

Lock 86_ge_lock_7S(x3) needs to be printed 3 times; lock 87_ge_lock_10H(x43) needs to be printed 43 times; - All parts are divided in such a way that you will print them with the smallest number of support structures.DLP/SLA 1.0 version features:-...

Credit for the creation of the platform goes to 3D artist Nello;- All parts are divided in such a way that you will print them with the smallest number of support structures.DLP/SLA 1.0 version features:- Contains 10 parts;- A printed model without...

The 3D printing model's chosen scale is 1/16 for the FFF/FDM version.VERSIONS SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 54 parts;- When printed the model stands 294 mm tall, 205 mm wide, 252 mm deep;- Minimal recommended 3D printer build...

The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 15 parts;- A printed model is 263 mm tall, 101 mm wide, 127 mm deep;-...

The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 35 parts;- A printed model is 326 mm tall, 229 mm wide, 209 mm deep;-...

The 3D printing figurines' chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 24 parts;- A printed model is 330 mm tall, 325 mm wide, 325 mm...

The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 16 parts;- A printed model is 246 mm tall, 112 mm wide, 119 mm deep;- Made...