loom tool 3d models

I reimagined the svg of simple frame loom, elevating it into a three-dimensional format and tweaking several aspects. I'm considering integrating a ratchet mechanism at the ends, which would enable weaving lengths exceeding two inches. The short...

If not, use two zip ties in a figure-eight configuration: one snugly wrapped around the loom and another through that one, but loose enough for the badge snap to latch onto. This arrangement is very effective and straightforward. For this solution,...

The pit for the head part becomes a bit steppy, which showed to be useful as the rough surface better holds the head part in place, when rotated under tension. I decided (and recommend) printing the loom in PETG. The problem I encountered with PLA...

After experimenting with various solutions and figuring out how to print pieces in one go that could be assembled, I came up with this rubber gun design using loom bands. My kids have bought so many of these bands already, but here's a new purpose...

... that the original files generated when sliced in PrusaSlicer 2.3.0 alpha4. I strongly recommend using knurled thumb nuts, or at the least, wing nuts, to secure the right side frame since it will need to be removed every time the loom is warped.

MEDIEVAL MINIATURE LOOM NATIVITY SCENE SCALE FIGURES PLAYMOBIL Check the print settings so that the threads slide smoothly. For the mobile frame I use a small piece of filament finishing off the ends with a little heat, you can use a simple lighter.

I noticed that the bottom of the stand gets close to the factory loom holder, so I added an attachment point to accommodate it as well. Print Settings: Printer Brand: Robo 3D Printer: R1 PLA Model Rafts: No Supports: No Resolution: 200 Infill: .10...

I use this clip with the Bullseye duct horizontal wire management style, which involves the cable management channel on the Bullseye and Petsfang pulling the loom in a horizontal direction. The built-in Ender 3 extruder clip fails to hold the wire...

This is a custom bracket for a Reprap Prusa I3, designed to sit atop and securely hold the wire loom and bowden tube in place. The interior dimensions of the bracket are carefully crafted to fit snugly around the prusa frame, with an inner diameter...

... If you don't think your printer is calibrated enough, cut the models in your slicer into small test pieces first.No brims or rafts unless you know you absolutely need it.No supports.For more loom models, visit my Loom collection on Printables.com.

Since the right side of the frame has to be removed in order to warp the loom, I placed nuts between the tubes and the right ride frame. You can either turn the nuts so they line up with the nut retainers perfectly, or ream them out to slightly...

This is a personalized version of the design available at http://www.thingiverse.com/thing:165857, which was created using the Customizer tool found at http://www.thingiverse.com/apps/customizer/run?thing_id=165857. ...To print this item, adjust the...

A personalized version of http://www.thingiverse.com/thing:165857 was created using the Customizer tool, with 6 pins and default settings. For specifics, the customization included an inner size of 9, one notch, a pin height of 18, a pin wall...

Customized version of https://www.thingiverse.com/thing:3564595 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3564595

Customized version of https://www.thingiverse.com/thing:1223978 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1223978

Customized version of https://www.thingiverse.com/thing:1697329 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1697329

Created using TinKerCad July 31, 2022. This is a 4 epi (8 epi double warp). ...Can be used on a side arm frame that can be adjusted to any desired length.

In order to ready the equipment, one must follow specific steps to ensure proper functioning.

Create your own clothing designs with a Makerbot? Amazing! Check out this project by Chilean designer Mauricio Rojas, called "Telar para Valentina." This maker printed the plastic parts using approximately 1 lb. of white ABS 3mm filament (printed at...

Remix of https://www.thingiverse.com/thing:6477624I rounded the corners and created multicolor modelsFor the pins use 3d nails, cut to about 18mm long.

This customized version can be found at http://www.thingiverse.com/thing:165857 and was created using the Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=165857). To print, set build_plate_manual_y to 100, build_plate_manual_x to...