loom tool 3d models

... bit also, making the tension of the fabric on the loom a little bit uneven. So I remixed the tension braces to fit a larger tension rod and a second slot to put the original tension rod on the bottom of the brace to solidify the loom width-wise.

Small clip with screw hole for holding 3/8 inch split wire loom cover to any surface. ...I printed mine on the Ender 3 in both PLA and PETG and both work fine.

Small clip with screw hole for holding 3/8 inch split wire loom cover to any surface. I printed mine on the Ender 3 in both PLA and PETG and both work fine. ... Category: 3D Printer Accessories

Chair dimensions 600x660xh1150mm Table Dimensions (Length * Width * Height): 180x75x1050 cm You can order the manufacture of chairs by clicking on the link - https://konyshev.net/catalog/stulya_1/karkas_loom/

However, upon investigation, I found that most available options for 1/2" split-loom were undersized, specifically targeting a 1/2" outer diameter rather than the desired 1/2" inner diameter. The first uploaded design has an inner diameter of 17mm...

I modified the single-hole heddle to be one half of an 8 (technically 8.1) dent reed for a 10 inch frame loom. ...Print two and connect them with a half-inch (actually 3/8") dowel rod.

It has 2 zip tie locations to attach the wire loom for your direct drive setup. I retained all of the original mount locations and attachment points for the x-axis limit switch. Print this dragon side down and no supports needed. ...I also printed this...

First time I saw a roping loom model was about ten years ago in the Corderie Royal (Royal rope factory) in Rochefort (which I recommand the visit by the way). Since then I want to do again the demo I saw there. Eventually this is a tool that has...

First time I saw a roping loom model was about ten years ago in the Corderie Royal (Royal rope factory) in Rochefort (which I recommend the visit by the way). Since then I want to do again the demo I saw there. Eventually this is a tool that has...

Name: c Type: model Format: 3Ds Max 2013 Export: FBX, OBJ, 3DS, MAT Render: VRay (3.x), Corona (3) Polys: 550233 Verts: 551824 Units: Millimeters Dimension: 2132.86 x 1524.0 x 854.96 Modeller: Artem RAdionov Preset: FULL CUSTOM Manufacturer: Baker...

minor update and a few modifications to my bed wire management clamp(works best with 3/8" automotive wire loom) Mostly just added an angle upward slightly for more even flex and made the mount wrap around the loom instead of inside to give wires more...

This object would have been used as a weight in a vertical loom to maintain tension on the warp threads (hanging vertically), between which the weft threads (horizontal) intertwined, forming the fabric. It is one of the few components of the loom...

The stepper motors are now covered and the cable loom is supported. Minimal support is required if printed with the cable entry hole on the bottom. Will fit on an Ender 3 Pro build plate when at 45 degrees to the build plate. Will require glueing or...

This object would be used as a weight on a vertical loom to keep the yarn threads (hung vertically) under tension, while the warp threads (horizontal) intertwined between them formed the fabric. It is one of the few components of the loom that...

Minor tweak and some refinements to my bed wire management clamp (works best with 3/8" automotive wire loom) - primarily added an angle upward slightly for more even flex and modified the mount to wrap around the loom instead of inside, giving wires...

This object would be used as a weight in a vertical loom, to keep the warp threads (hanging vertically) under tension, between which the weft threads (horizontal) intertwined, forming the fabric. They are one of few components of the loom that...

This object would have been used as a weight on a vertical loom to keep the warp threads (hung vertically) under tension, while the weft threads (horizontal) intertwined between them formed the fabric. It is one of the few components of the loom that...

Mainly, I added a slight angle upward for smoother flex and modified the mount to wrap around the loom instead of inside, giving wires extra space. •NOTE:. * No mounting hole exists due to the wide range of beds, carriages, and other unique designs....

I mistakenly purchased a 1/2" split loom instead of the intended 3/8" size that Ben had recommended, so to avoid unnecessary delays and returns, I modified the original design files on my computer to accommodate the larger diameter, allowing me to...

Thanks to rjrahardjo for the three rigid heddle holder! ... As I just need a double one on my Ashford Knitter's Loom and the original wooden one is about 40€, I just cut the three one. ...Therefor right and left is the same one.

Astronauts are going to love this amazing water loom designed specifically for them! It's perfect for separating water and liquids in zero gravity, or just for having some fun in space. The liquid separation is mesmerizing as it floats freely in the...

... design (www.thingiverse.com/thing:350438) into the bracelet system for expedited assembly. ...The neighborhood children eagerly adopt the loom, while my limited reach confines me to being the primary recipient of their creative handmade gifts.

This small clip is designed to securely hold a 3/8 inch split wire loom cover to any given surface using its screw hole feature. ...I successfully printed mine on the Ender 3 in both PLA and PETG, verifying that they function perfectly.

I designed this to keep the wiring and filament guides secure and organized after installing the Flexion extruder kit.\nIt boasts several features:\nSecures loom wiring safely and neatly.\nComes equipped with slots for wire ties around the...

The stepper motors are now covered and the cable loom is supported. Minimal support is required if printed with the cable entry hole on the bottom. Will fit on an Ender 3 Pro build plate when at 45 degrees to the build plate. Will require glueing or...

I noticed the clamp supporting the extruder/head end of the sleeved wiring loom on my Duinotech tl-4090 wasn't doing its job - it simply didn't reach the loom.\nRather than replacing the metal bracket with a flimsy plastic one, I decided to create a...

Here is the spun text: Minor tweak and several adjustments made to my bed wire management clamp *(works exceptionally well with 3/8" automotive wire loom)*. The primary focus was on adding a slight upward angle for even greater flexibility and...

Replaces the magnetic filament sensor holder on the AnyCubic i3 with a neater setup.\r\nAlso holds the cable loom in place for a more organized print job :)\r\n\r\nRemove the magnetic half-dome piece from the printer and swap it out with this new...

The Faber-Castell Loom fountain pen holder/stand is a game-changer. I was blown away by the quality of this affordable pen, but it's missing one crucial thing: a convenient place to store it when not in use. This clever solution fits the bill...

This remix of @jschrier's French knitting loom now offers an added feature - a groove at its base that can be easily fitted over a convenient length of pipe or hollow wooden tubing to serve as a handle. When utilizing this groove, you will likely...