longer ray5 air assist 3d models

Not having the laser unit in hand yet I took measurements from another design by Vince Fero (i think) that i can no longer find and reference. I'm yet to print this so I'm not sure if/how it will work. The idea is to have a narrow air stream at...

These are clamps and guides I made to route the hose for the Longer ray5 air assist. these allow the hose to be run cleanly, without having to ziptie the hose and crimp it. The clamps are held in place with the enclosed small ziptie hole in it. the...

Longer Ray5 5w Air Assist duct

Longer Ray5 5w Air Assist duct

This air assist for the Longer Ray5 10W module uses only two 3M screws to hold it in place. I used some 4mm Inner, 6mm Outer air hose.I printed it with a raft to help hold it down and you don't need to use supports if your printer has good...

https://www.tinkercad.com/things/5uoej8Z9NrG ______ WIP for AIr Assist to be use with laser LONGER RAY 5 One can use 3.9mm tube (aquarium or capricorn petg outer diameter) or edit file to use other outer diameter tube This object was made in...

Vous pouvez éditer le fichier TINLERCAD pour utiliser un tube d'un autre diamètre.https://www.tinkercad.com/things/5uoej8Z9NrG WIP for AIr Assist to be use with laser LONGER RAY 5 One can use 3.9mm tube (aquarium or capricorn petg outer diameter) or...

Air assist for the Longer Ray 5 laser engraver/cutter. 03/03/22 -Added dual cone design. Opening at nozzle for laser should allow the same cooling air flow as the stock shroud/nozzle. May need a small bit of glue or silicone sealant on air...

Air Assist mount for Longer Ray 5 Works with 5W and 10W module Air hose clamp included

This is an air assist nozzle for the Longer Ray 5 Laser engraver. It accepts a 6mm outside diameter tube. Note: after installing this nozzle, you can no longer use the aluminium spacer to calibrate the laser. Instead, you have to measure from the...

Air assist for my Laser Longer Ray 5. I use a 6mm outer diameter silicone tube stiffened with electrician's tape. The exit nozzle is 2.5mm and is aimed at the point of laser impact. I use it with an ACO-318 aquarium pump. ... There is...

The only thing missing on the Longer Ray5 laser cutter and engraver https://youtu.be/oU47QBuMxX4

If anyone from Longer is reading this please make the wires to the laser 4-5 cm longer (no pun intended). The connecting brackets on the other hand do require some supports and a superglue. The parts are named in groups and I think it's a pretty...

... en PLA. Elle vient se placer sur la tête Laser et permet d'obtenir de meilleurs résultats lors de la découpe.Vous injecterez l'air comme vous le souhaitez. Christian utilise un ventilateur dont il récupère la sortie pour l'envoyer sur l'Air Assist

Laser Engravers Little Helpers (might add some more once ...) Designed for the Longer Ray5 Please leave a note if youre using a different Engraver that it works with.

The "upper_bracket" is made to fit the Longer Ray5 10W backplate, but could be adapted for other lasers. The two brackets are meant to be connected by a standard M6 x 60mm bolt. The M6_threaded knob prints with threads 3D printed internally. The...

This is a fine height adjuster for the Longer Ray5 10W laser engraver / cutter. It consists of three 3d printed parts, connected with a standard M6 x 60mm bolt. The "lower_bracket" should fit most laser modules that have machine screws on 32mm...

This is for LONGER Ray5 10W Laser Z-Axis. Bottom part (4mm)- middle hole is to be tapped with 1/4" tread and place a 1/4" screw with head sitting on the bottom (treaded part to point upwards). Two smaller holes on the side a for 5mm guide pins. Top...

I Made this feet for the Longer Ray 5 so you could hold it in place, or remove it without using a screwdriver. on Top there are Distance Feet to put the laser on all corners higher. 10 and 20 mm. I made stl a little new with thicker walls. ... I...

For raising Longer Ray 5 laser up to use a rotary. printed at 0.28 MM layer height. 50 percent infill. use supplied screws to mount three straight legs. My screw holes were a little offset which is reflected in this model but might not work with...

Air Assist mit Diodenhalter für K40 Laser

Clips pour maintenir les courroies proprement contre le châssis du graveur.

I designed this air assist for my flying bear LASERMAN laser, It is 21mm high perfect for focusing the laser.

Designed to allow cooling air from laser fan to have the same amount of airflow to exit as the stock shroud, and keep the air assist pressure from altering the laser fan's cooling function. ... Hose connection is 4.75mm which fits generic aquarium...

Here is the rewritten text: A simplified air-assisted system designed specifically for the Elekslaser 2500mW laser cutter. ...Constructed from 4mm thick plywood, this system utilizes a ball pump needle as its precision nozzle.

Air Assit CNC laser

I've not tested this print yet, but I saw a chance for improvement from [toaof999](https://www.thingiverse.com/toaof999/designs) [version](https://www.thingiverse.com/thing:5182282). ... https://www.thingiverse.com/thing:5182282

This is a remix i found on printables by Fabian of a Height calibration cylinder holder. ... I remixed it to also hold the micro sd card adapter the RAY5 comes with, since i am always misplacing them.

Riser for the longer ray 5 that can work with the mounts created by BusterBeagle3D here. https://www.thingiverse.com/thing:4917083/files by https://www.thingiverse.com/BusterBeagle3D you can use the risers by themselves or they can fit...

<p>This is a simple plate that is 3.8mm thick with a little handle on one side.&nbsp;</p><p>To use it, lower the acrylic guard down onto this plate and tighten the screws. &nbsp;Then the laser will be in focus for the material you are...