longer orange 10 3d models

Here I made a scale model of the Longer Orange 10. I'd say its about 90% accurate as some things needed to be more thick to print. Space under the vat makes it so if you print in transparent resin, you can put a light under it. I don't...

Dripping support designed for LONGER Orange 10, to drip tall object. ...Slope of support is 15 degrees

This frame slides seamlessly over the stock cover on a Longer Orange 10, providing a precise fit for the three rubber bands that secure the plexiglass in place. ...The design was meticulously crafted based on a model, and although I don't own an Orange...

The specialized dripper system has been engineered specifically for the LONGER Orange 10, allowing it to efficiently deliver a steady stream of lubricant directly to the top of the rifle's components. ...The custom-designed drip path slopes upward at an...

Edit it online https://www.tinkercad.com/things/3742whQijyl FR It's a dripper for the printing plate on a LONGER Orange 10 and similar printers... It keeps the printing plate at an angle (30 degrees) above the resin vat so that excess resin can...

This is a drip stand for the print plate on a LONGER Orange 10 and similar printers. It holds the print plate at an angle (30 degrees) over the resin vat so that excess resin can drain off and back into the vat. This stand can remain mounted to the...

Built from the Elegoo Mars drip bed attachment, this model is specifically designed for the Longer Orange 10.

Corner caps are used to bolster an acrylic case, replacing rubber bands on the Longer Orange 10. ...It's advisable to use Gorilla Glue, either instant or assembling type.

2 x simple vat covers for the Longer Orange 10. One has a hole to add a knob if you want. No I'm not adding a design for 1 as there are plenty out there. The picture is of the first version of the no-hole one. It needed some tweaking but as it did...

Goal: - Replace the ultra noisy 60mm OEM Longer Orange-10 Fan. - Use a standard 120mm CPU fan laying around my spare parts. - Keep the original metallic bottom plate. - Minimize or avoid any additional screw / reuse screw from OEM bottom. ... - Make...

At this point I printed one set of v0 and it is waiting for time to be tested !!! Goal: Replace the ultra noisy 60mm OEM Longer Orange-10 Fan. Use a standard 120mm CPU fan laying around my spare parts. Keep the original metallic bottom plate....

I'm looking for a very basic vat cover for my Little Longer Orange 10. I've seen a couple of designs for the Orange 30, but only one other option exists for the 10 and that's a bit too expensive for what I need. This is version 2. Version 1 worked...

A friend gave me a Longer Orange10. The rubber band broke and the cover started to fall apart. I tried tape but then realized I a printer. The images shown were printed with my Prusa mini+. ... Part was designed using Onshape.

A friend gave me a Longer Orange10. The rubber band broke and the cover started to fall apart. I tried tape but then realized I a printer. The images shown were printed with my Prusa mini+. ... Part was designed using Onshape.

A friend gave me a Longer Orange10. The rubber band broke and the cover started to fall apart. I tried tape but then realized I a printer. ...The images shown were printed with my Prusa mini+.</p> <p>Part was designed using Onshape.</p> Category: 3D...

Voici un système d'aération permettant de filtrer l'odeur de résine à l'aide d'un ventilateur 40x40x10 5v , un arduino pro micro et du charbon actif. ...Mais aussi un compartiment pour y ajouter de l'huile essentiel afin de laisser une bonne odeur dans...

Tired of struggling with the poorly placed knob screw that's right next to the VAT of Longer Orange 30? Get ready for a solution! Ready to use in under 30 minutes, no supports or Brim required. When the print is complete, simply press the screw knob...

After installing the Wham Bam Flexible Build System for the Longer Orange 10 (https://whambam3d.com/products/dwr-102-x-59) and adjusting the build plate for the new height, the build plate assembly no longer fit onto the drip support, because the...

After installing the Wham Bam Flexible Build System for the Longer Orange 10 (https://whambam3d.com/products/dwr-102-x-59) and adjusting the build plate for the new height, the build plate assembly no longer fit onto the drip support, because the...

A replacement for the stock 60mm fan that fits a standard 120mm computer fan has been installed. ...As a result, the printer is nearly silent.

you can go either way, just screw into the plastic (m3’s) or, open the holes up a bit for the heat set insert (11/64 drill bit) Set that aside and take your printer apart, the pictures show the orange 30 procedure first, followed by the orange 10...

Longer 3D Printing Experience with a Durable Drip Tray for the 10 Orange Printer. ... Printed directly on the highly-regarded Ender 3 PRO, utilizing robust support structures to achieve optimal results.

Designers craft 3D orange vats with precision, showcasing a 10-gallon cover. ...Expertly printed on the versatile Ender 3 Pro, this model demonstrates exceptional engineering skills.

... at an angle in order for the resin to drip off before removing the part from the machine. No supports needed. Short mount demo: https://www.youtube.com/watch?v=UbHaHGRBZQQ Longer orange 10 review: https://www.youtube.com/watch?v=B9uNtXIZb8Y

... ...Edit it online https://www.tinkercad.com/things/cAPufNojbHm This is a remix of a design by greavousbee for a vat cover on a longer orange 10 resin pronter. i decided it needed a handle. ... https://www.thingiverse.com/thing:4070468- origional

Cover Holder for Longer Orange 30 with built in lever for activating the level switch.

Resin vat cover for the Longer Orange 30. ... I designed it with a generous depth for unknown reasons, but feel free to adjust the dimensions using your slicer to minimize excess filament usage.

Parts to enhance the lid of the Orange 30 should fit together seamlessly but utilize glue (plentiful amounts recommended) if you plan to detach the rubber bands holding this subpar lid in place, resulting in an improved appearance. This modification...

Parts to improve the lid of the Orange 30. Should snap in place but use glue (copious amounts recommended) if you plan to remove the rubberbands holding this travesty of a lid together. ...Makes the lid look a bit nicer too.</p> <p>I realized that the...

Stability bracket for Longer Orange 30 Z axis front mount part