long axis drag 3d models

Drag chain for AM8 metal frame upgrade. Small zip tie slots have been added and one M3-8 screw and M3 nut are needed to attach x mount to x-z mount. Also needed are 3 M3-30 to mount the x motor. ... Extending wire from print head to main board is a...

This remix includes enough clearance under the stepper for safely disconnecting and reconnecting its cable, while extending the drag chain interface by 30mm to provide more space for filament to enter the extruder smoothly. ...With a single bolt holding...

Just my remix from Drag Chain - Cable Chain - Ender 3 by diogosantos88 June 26, 2019 for the TEVO Tarantula Pro. (not letting me tag the remix when uploading). The Ender has a 40mm X carriage and a 50m however the TTP has a 45mm. Also a different...

I must figure out how to create wiring extensions for the hot end, extruder motor, y-axis stepper motor, and the y axis stop switch.\r\n\r\nThe links work perfectly otherwise. The orientation is spot on, and the attachment points on each end are...

I'm using BMG clone extruder and the cable guide from llueen can't be fit directly - Z-axis brass nut blocking part of the guide. I have to remove some parts to get it fit. * llueen cable guide: https://www.thingiverse.com/thing:4723800 Also,...

The Y-axis bed connector I use comes from Tobi0892 design: https://www.thingiverse.com/thing:4316238 I am using a total of 35 chain-link (15 for Y-axis and 20 for Z-axis) and 3 chain-link-cut for the Z-axis. ... Edit: I added the file clip_connector,...

The drag chain has got a new position for the V0.2, where the radius has been reduced in comparison to the V0.1 design. As a result the chain contained in my kit didn't work with the new position. For this I designed this longer spacer so that the...

The X-Axis Drag Chain Guide is engineered specifically for the Y-Axis Drag Chain to prevent it from deviating along the x-axis while in motion.

I jointed the dual dampener for x axis and drag chain in meshmixer.

Remix z axis drag connector to fit over heat sink on my Z axis stepper motor (from thingiverse.com/thing:5205630).Supports required

As there was no exact drag chain for the X axis on a CR10 Smart PRO, i decided to make one.You will have to remove the bottom of the printer and disconnect the bed cable and feed it through the holes in the base mount, screw and nut.It takes 12...

I placed the drag chain on the X axis away from the frame so it should almost remain its full build volume without the need of replacing the filament mount. The drag chain in the pictures are bending backwards because I made some iterations of the...

This remix is a combination of the Z-Axis Drag chain mount from Gunderson99 (thing:5636013) & the Filament roller guide from OpenDorrPolicy (thing:4811491). ...

This was printed with ABS, no supports are needed.BOM:1 - 10x11 Drag Chain6 - M3x6 Flat head screws (Attach the drag chain to the mounts)2 - M3x10 Button cap screws (Attach the support brace to the gantry)2 - M3x10 Flat head screws (Attach the mount...

I encountered a problem with the Z axis drag chain snagging on the Z back plate screws. To resolve this, I designed and fabricated a custom bracket to secure and keep the drag chain at a safe distance from the Z back plate. ...Additionally, I crafted...

My Shapeoko 5 Pro showed up with a cracked, bent and warped X axis drag chain mount. This is a (close enough) matching part that fits as a drop-in replacement with the regular screws. The standard screws are threaded for M3, I recommend heat...

I upgraded the MPCNC's Z-axis drag chain/cable carrier to withstand the rigors of its heavy-duty drag chain, which was consistently causing failures in the original design. ...To compensate, I significantly expanded the carrier's dimensions to...

... two 3mm button head bolts measuring 8mm in length. This project was inspired by a reddit post discussing a 3D printed bracket for the X-axis drag chain: https://www.reddit.com/r/shapeoko/comments/7846hn/3d_printed_bracket_for_xaxis_drag_chain/.

This was printed with ABS, no supports are needed.BOM:1 - 10x11 Drag Chain6 - M3x6 Flat head screws (Attach the drag chain to the mounts)2 - M3x10 Button cap screws (Attach the support brace to the gantry)2 - M3x10 Flat head screws (Attach the mount...

These are the drag chain mounts for attaching 15mm x 10mm drag chains to the print bed plate of the Wilson II model. The user installed a Prusa i3 print bed plate, modified to fit the Y-Table from the Wilson II model. ...To secure the base, use one of...

Another drag chain for the Y-Axis of the Anycubic I3 Mega S. You need a 7mm x 7mm drag chain, like this one: https://de.aliexpress.com/item/1005004692804703.html?spm=a2g0o.order_list.order_list_main.4.42b45c5fKAAbJJ&gatewayAdapt=glo2deu You also...

This is the Z-axis drag chain mount that matches the XY-axis set I designed right here. http://www.thingiverse.com/thing:1272581 I made EMT clampholes for four bolts and nuts, but you only need two in each one. Seriously, stop over-tightening it -...

This is the Z-axis drag chain mount that matches the XY-axis set I designed here. http://www.thingiverse.com/thing:1272581 I made EMT clampholes for 4 bolts and nuts, but you only need to use two in each one. No seriously, stop tightening it. :) You...

This is the Z-axis drag chain mount that matches the XY-axis set I designed here. http://www.thingiverse.com/thing:1272581 I made EMT clampholes for 4 bolts and nuts, but you only need to use two in each one. No seriously, stop tightening it. :) You...

X Axis drag chain complements Y and Z axes drag chains, available on Thingiverse at https://www.thingiverse.com/thing:2757810 and https://www.thingiverse.com/thing:2708420. Drag chain assembly designed specifically for CR-10 to manage cabling from...

Here is the text rewritten in American English, with a Flesch-Kincaid score of 100% and following all the rules: This remix connects the "Drag Chain" links from diogosantos88 to the 2020 frame of the Ender 3 via click system by Johnniewhiskey. ... I...

!NEW! ...Version: https://www.printables.com/model/288965-new-v-minion-drag-chain-assembly-v2-zx Updated version of ZX JUNCTION (V2) that mounts to the X motor cage rather than the X axis extrusion, you will need included X_motor_cage_V2.

I designed a custom open drag chain specifically tailored for the Y-axis of my CR-10 V2. Unfortunately, other chains I downloaded were intended for different versions of the CR-series and didn't quite fit properly at the start and end points. ...To...

**Update March 10, 2021:** Realized where the drag chain connects on the hotend part interfered with the left side vertical extrusion and prevented the hotend assembly from hitting the x-axis endstop to home. ...Moved it just far enough along the x...

On my first Shapeoko 5 Pro print, I crushed my right-hand Y axis drag chain mount by crashing the Sweepy (that I had set to the 4:30 o'clock position instead of 6 o'clock) into it while zeroing a bit. This is a (close enough) matching part that fits...