logo porsche carrera 3d models

Instead of painting the Dyna-Soar shield logo I now plan to print it out on high gloss photo paper, seal it, and then glue it over the raised shield. I think that will look much better. Hope to get some more done soon and update the post! ...

I also upload the firmware binary file (firmware.hex - ITALIAN LANGUAGE!) as well as the _Bootscreen.h file in which, to make the difference with the original firmware more visible, I made the same initial logo but in negative. CONFIGURATION...

(Support Enforcers Only)Super glue works best.Resize for smaller or larger use.Clean your build plate with dish soap to ensure the floor of the Modules do not lift off (long build). Other parts to use with the Space Port Power Station:The original...

Citizens will sleep safely knowing the power generated will light up the dark passageways used by heavily armed patrols, keeping the alien mutant scum from crawling into your hab, slitting your throat, and taking what's yours!Shelter...

Place your ducts with 2x M3 bolts.You can adjust the height of the ducts later.Then place 2 x 5015 cooling fans with M3 nuts and bolts as shown above.Fix 40mm fan and Cover-With-Logo with 4x M3 bolt to the main body.-Place snap on Duct-Left and...

Worlds are waiting.Equip yourself today, citizen!Space Port - https://www.printables.com/model/205432-space-port-terrain Starship Cargo Pod - https://www.printables.com/model/224797-starship-cargo-pod Starship Transfer Tug -...

(After repairs of course)Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

A rating or tip is also welcome and may check out my other designs! Happy printing!  Print instructionsAll parts are optimized for FDM printing.Please use a 0.4mm nozzle (or smaller).I advise to use the .3mf (or gcode) files, as all...

It will accommodate the RAK5005-O base board plus the RAK4631 (LoRa), RAK1910 (GNSS/GPS), RAK13002 (IO), and RAK18001 (piezo buzzer) modules.There are seven files required for a complete case, as well as socket head cap screws and micro push button...

It will use slightly more than half of the spool.0.30 Height and rectilinear infill (Slic3r) will make it strong with a nice look to the side words and will take ~21 hours. There are 2 types of lids, one for a multi-material unit and one for those...

Also take a look at my other Designs!Changelog:Added a MMU version of the display coverAdded Beam with Prusa Printers logoSmall adjustments to the print filesAdded a color upgrade for the side partsAdded a symmetric version of the casingAdded an...

... All my designs are free, they're developed and tested in my spare time and most have source files available for easy editing. If you enjoy this or any of my other designs, a small donation is not needed but welcome. Thanks! :)

This required cutting out a circular section and removing the MakerBot logo stamped within (sorry MakerBot). This section was later placed on top of the cylindrical puzzle piece. ...Two small pegs were placed in the resulting hole, that would fit into...

Also note that the “X” logo in some of the pics are owned/trademarked by SpaceX. ** Material:** I used PETG for this print because it is UV resistant, and I wanted it to be strong, durable, and survive long-term out in the elements. ASA would...

Note that I made this as a birthday present, that's why there is decal/logo on the chamber in the photos, but there is a version included without decal... Print instructionsInfo The chamber consists of four parts, two are optional. You should at...

The variants are as follows: There are 2 slot sizes (distance between the prongs of the clip): 0.25mm, for cardstock and photographic paper (1-sided or even 2-sided) 1.5mm, for thicker punchouts, plastic pieces or encapsulated cardstock (like the...

Bob https://www.thingiverse.com/thing:5415032 Nurse Piggy https://www.thingiverse.com/thing:5410272 Mahna mahan https://www.thingiverse.com/thing:5391356 Muppet signs https://www.thingiverse.com/thing:5327083 Muppet Theater...

Names and Logos are all fictional, yet close to the original for believability. All textures are available in high resolution, exported from Substance Painter using export presets for Unreal Engine 4; CryEngine3 and Unity5 aswell as default channel...

Needs to be glued - logo and markings on TK_window point in the same direction. ...TK_Cap_52 In case you don't trust an all-printed cap, you can use this part alongside a windowless TK_ring and a 52-77mm to create a rear-cap that attaches to this QR...

If higher gear ratios are needed a 2nd set of gears will be needed, this design uses only one planetary gear set.\n\n \n \n Update Log\n10/22/2016 Added a 1:9.8 gear ratio, 3" (77.4mm) gearbox, which pushes the limit of torque possible with thin PLA...

My final changes were minor, and purely cosmetic: I added an additional curve to the rear section of the base, and picked a nice font to slap a recessed "GT3" logo on the (now wider) pedestal part of the stand. The finishing touch was to add 4...

Three options are provided with and without material choice clearly printed on the side along with appropriate recycling logo. Shield: The shield is optimized for 12"x12" stock that we had available and is cut to be 11.5" wide. The hole placement...

I also named it the aperture box as it looks very similar to the Aperture Science logo from the Portal game universe. It is opened by twisting the handles on the doors in a clockwise direction.</p><p>This was originally uploaded to Thingiverse in...

Details are on but will need supports and will likely be very fragile.Print separately:borealis_keelborealis_iceterrainPost-PrintingIce TerrainPrinting out the terrain with white filament works well enough, but I've attempted an interesting technique...

You may want to use a brim on the pins. Print instructionsSupports: No Resolution: 0.10mm Infill: 30% Notes: All models can be printed without supports, definitely don't use them on the working model. The Slide In Split model should be printed with...

For your convenient display, the model is provided with a platform that has a large Overwatch logo engraved on it. The 3D printing Vigilante is a living picture of the fearless warrior who is ready to give his all in order to find out what really...

I might want to make a magnetized way of attaching the 15mm clamp but that's for later. UPDATE7: (3/21/2020) MOVED TO PRUSA! Ill be doing a tutorial on how to make in a HOT hot second &lt;3 gada, get my mini first :( Updated: -Flag is lighter and...

To accomplish this in Cura, set the Skin Expand Distance to a high number like 10. Some of My Designs Click an image below (opens in a new tab) or go to my designs page and see them all. If you see some thing that you like ,please click the Like...

Be generous, you can always shorten it later.Pick one direction to be up, I used the side with the printed logo. For each switch, mark it with the direction it triggers. This is reversed though. So if you push the stick up, the switch facing you is...

the small part of the Handy logo was going to be used as a wedge part for the now classic version of the Handy Holder that is belt/strap/vesa mountable. 8. Handy Grease applicators - fit in the slot of the Handy, just squeeze your grease tube into...