logitech z506 mount 3d models

I was looking for a way to mount my Logitech C270 webcam to my camera tripod and while I like the design from Jet_Prints I didn't want to deal with taking it on and off the old quick release plate. ... So I combined the two so now I have a seperate...

I remixed the Anycubic i3 Mega C170 C270 Cam Mount by Bishbish2000 to fit the Logitech C270 webcam perfectly. ...Since I didn't have any M6 screws or nuts, I adjusted the bottom hole to accommodate a M3 threaded insert with an outside diameter of 4mm,...

Single Logitech C720 Web Camera Mount for the sidewinder X1. This mod demands two additional longer M3 bolds (10 or 12mm) and an M3 8mm+ for attaching to the camera. ... Also recommend checking out https://www.thingiverse.com/thing:3081838/comments to...

Mount for Logitech C270: Two Printing Options Available A compact design is available, however it takes up a small amount of space on your build plate due to the camera's position. ...A second option relocates the camera slightly further back,...

This bracket enables you to securely attach a Logitech C270 HD Webcam to a Guerrilla tripod. To begin, simply detach the original webcam bracket and replace it with a small screw that will firmly hold the webcam in place on the 3D printed bracket.

I am designing a mount for my Logitech C279 webcam that utilizes the tube of a one-inch wire shelf as its foundation. ...The simplicity of this design is striking, requiring only the opening of the base to allow the camera to be inserted directly into...

These adapters work for both right and left sides, mounting securely to the sides of IKEA Jerker desk pillars. I printed them using PLA at 100% fill density. ... Print Settings Printer: Raise3D N2+ Rafts: Yes Supports: Yes Infill: 40% Notes: Printed...

Simple desk mount designed specifically for the Logitech steering wheel, yet likely compatible with various other brands as well. A clever slide mechanism enables a precise installation of the wheel under your desk, where visibility is limited. ...For...

Mounting the Logitech C270 camera to the Ender 5 printer involves reusing the original pin from the camera. To do this, you will need a few additional items. ... Required components include one M3 bolt, one M3 nut, and two other critical parts: an M4...

I'm utilizing a Logitech Quickcam Pro 9000 as my webcam and sought to install it without encountering vibration interference or any alteration to the camera's performance. Since I already possess mounts fashioned from 1/2-inch PVC pipes, I...

Here's another innovative mod designed by volkmste for Logitech cameras that seamlessly integrates with the stock mount, requiring no modifications. ...I've refined the design to eliminate unnecessary curves while ensuring a smooth print with minimal...

We are using these mounting brackets and a pair of Logitech C270 cameras along with OctoPrint to record timelapse videos of all our 3D prints at TheLab.ms makerspace. Category: 3D Printer Accessories

This is a simple mount for my Logitech C270 cam. The Baseplate holes fit to the original Stuva board holes. ... What you need: 2x 3.5x16 Wood-Screw for the Baseplate 1x M5x16 Screw with Nut for the Connection to the Arm 1x M3x20 Screw with Nut and...

I integrated two vibrant NeoPixel Sticks into my Logitech camera mount, injecting a burst of color and creativity into the setup. ...These innovative devices boast eight mesmerizing 5050 RGB LEDs, each paired with its own built-in driver for seamless...

A ceiling mount for the Logitech Expansion mic. I made this for my job and to practice my 3d modeling skills. Pretty sure nobody really needs this, but if someone needs this one day, you have it. It's for a 1¾ inch hole. ...2 inches should to it.</p>

This is a remix to a mount Logitech C270 camera to the Ender 5 printer. It reuses the original pin from the camera. ... Other things required: 1 x M3 bolt 1 x M3 nut 1 x M4 bolt (minimum 18 mm) 1 x M4 nut

I needed a simple replacement for the original mount on my Logitech C170. To remove it, I ran a hacksaw between the gap at the camera end and the blanking plate. Then, I used a round magnet from B&Q to secure it in place. ...If you ask politely, the...

LIttle file to add a GoPro mount to a Logitech 9000. ... You need to undo all the screws on the stock stand, some are under the rubber and reuse the existing screws on the little hinge directly attached to the camera.

This mounting bracket is designed for Logitech C525 webcam. Should works also for other webcam of the C500 series. Pressure for the webcam attachment is a little bit too weak. ...May need some double face tape to strength up the positioning of the...

Couldn't find a mount for the Logitech Rally conference camera that wasn't crazy expensive and couldn't find one on here either, so I decided to model it up myself. ...I used really good resolution and ABS because it will be visible all the time, but...

This is a bracket to hold a Logitech C260 or C270 webcam more securely than the built-in adjustable mount. Affix it to the top of the monitor with some double sided tape. Bracket holds the webcam tightly enough that it's not necessary to attach the...

A simple yet effective solution for securing your Logitech C270 webcam is a basic wall mount that relies on a medium-strength Command strip for attachment. ...To ensure a solid hold, an M3x20 bolt can be used to screw directly into the webcam, providing...

Just a very simple remix to mount a Logitech C270 webcam directly to the Ender 3 S1 or S1 Pro. The original hinge pin from the camera can reused, no additional screw and nut needed. ...This position comes with a unobstructed view of the nozzle.

Mount the webcam now to make it work with Logitech C270 and C310. Print Settings Printer Brand is RepRap. Choose Printer Prusa i3 Steel. No rafts are necessary. Turn off supports completely. Resolution will be 0.4 mm. ...Infill percentage will be 20...

This is a remix to a mount Logitech C270 camera to the Ender 5 printer. It reuses the original pin from the camera. ... Other things required: 1 x M3 bolt 1 x M3 nut 1 x M4 bolt (minimum 18 mm) 1 x M4 nut

This print is designed to allow mounting a Logitech C920 to the PrusaBox rail, without having to take off the mount that comes supplied with the camera. &nbsp;The original mount just slides into a square housing to hold the camera. &nbsp;The housing...

Attachment for a Logitech webcam in my Custom Cam Mounting System. Parts of the system include: Bed Mount: Designed to be easily attached, this model is available on Thingiverse at https://www.thingiverse.com/thing:2727347. Z-Axis Mount: A sturdy...

... 3D printed adapter. The adapter can then be easily slid onto the tripod in place of the standard camera mount. For additional information on this project, visit my blog at https://edditiveblog.wordpress.com/2018/10/15/3d-printed-webcam-mount/.

The lower mount allows for a clear view of the hotend from below, while the leveled mount provides an unobstructed horizontal view of both the hotend and printing surface. ... For optimal image quality, attach the Improved_Focus_Ring_for_C270, printed...

I design and manufacture a custom desktop mount specifically tailored to hold the Logitech G533 Headset securely in place. This innovative holder features a precision-cutout for the USB Dongle, ensuring seamless connectivity and optimal performance.