logitech x 530 replacement speaker 3d models

Human is speaking through a LOGITECH Z906 speaker system. ...A screw with a diameter of 6 millimeters has been removed.

Logitech's z906 speakers pivot seamlessly on three distinct axes of rotation, ensuring precise control over their placement and sound dispersal.

Speaker Bracket for Logitech Z313 Speaker controller (printed at 102% adjust based on printer tolerances) Folded Paper used as wedge on side without dial. ...(see pic 2) Used 2 small screws stolen from a nerf gun.

This is a mount designed specifically for a mid-range speaker used in Logitech's speaker system. ...The installation process requires six number 6 size screws to secure it properly.

I wanted my Logitech Z906 sound system speakers look more clear and neutral. The speaker design looked to much technical and not perfect for the living room. So i wanted a clean cover for the speakers. It fits nicely in the small gap on the side of...

Here's a design concept for a universal speaker mount that fits perfectly with Logitech Z533 speakers, allowing users to securely fasten and detach their speakers from walls without worrying about base instability issues. ...This versatile solution...

I wanted my Logitech Z906 sound system speakers look more clear and neutral. The speaker design looked to much technical and not perfect for the living room. So i wanted a clean cover for the speakers. It fits nicely in the small gap on the side of...

This is a speaker mount for the L&R speakers for the Logitech Z625 set. I designed it to be mounted with button head screws in the middle of a 2x4. ...There is a place to zip-tie the cord of the speaker to the mount.

This shelf was designed to hold Logitech speakers but would hold just about anything of similar weight. ...I used plasti dip in the channel to hold the sliding piece in the right place.

This lets you mount the Logitech Speaker Volume control and headphone jack under the front edge of your desk, while keeping access to all controls and ports readily available.

... audio experience, free from distractions caused by cluttered speaker placements. The Speaker hanger is an ideal accessory for anyone looking to upgrade their home theater setup and maximize the full potential of their Logitech z506 speaker system.

... gets pulled when raising desk, to avoid pulling the speaker off the stand).  Smaller part is washer which uses M2 screw and heatset nut to hold the speaker.  (Stand is slanted forward to point the speaker flat)I made this for Logitech Z2300 speakers

Rear satellite holder: 2x M6x60 hex or allen bolts, 2x washer, 2x M6 hex nuts to bolt the two parts together, 2x M6 x 25 hex bolts to attach the speakers, 2x M6 hex nuts to fix the speakers in position. The wall mount through hole is 5.5 mm, so you...

I remixed MelkerSimonsson's thing 2814335 to give it some extra bulk and a more polished look. It wasn't my finest work, but it got the job done. To avoid soldering altogether, I added a slit that makes assembly much easier. One challenge I faced...

An nice stand for my Logitech speakers Print instructionsCategory: Music Summary An nice stand for my Logitech speakers Print Settings Printer: Ultimaker Orginal + Rafts: No</div>Supports: No Resolution: 0.2</div>Infill: 5% Filament:...

Rear satellite holder: 2x M6x60 hex or allen bolts, 2x washer, 2x M6 hex nuts to bolt the two parts together, 2x M6 x 25 hex bolts to attach the speakers, 2x M6 hex nuts to fix the speakers in position. The wall mount through hole is 5.5 mm, so you...

The speaker grill for the Logitech Z4 is specifically designed to snap into place without the need for adhesive or other fastening methods. ...This secure and effortless installation ensures a seamless integration with the rest of the system, promoting...

I built this custom holder for my Logitech speakers using a combination of basic materials and advanced technology. ...To create this design, you'll require two essential components: screws to secure the device in place and a 3D printer to fabricate the...

To boost my audio experience on my Logitech Z906 surround sound system, I designed a kit to elevate my speakers higher. The base is engineered to fit perfectly onto Ikea KALLAX furniture. The pipe that increases the height of the speakers is a...

I replaced the old X530 surround and center channel speakers to build a more compact soundbar. Using a 25-watt amp, I wired the center speaker directly to a single channel at 4 ohms, while connecting the outer speakers in series at 8 ohms to the...

I wanted a speaker stand for my Logitech Z906 speakers, but i could not find any cheap once. So i decided to make one myself. This design uses the ADILS legs to act as a stand. I printed this att 0.2 layer height but could easily be greater to...

Highly detailed model of a top-of-the-line Logitech speaker.\n\nAdvanced texture and material development are not required, but rather the inclusion of these essential elements is merely hinted at for your creative expression.\n\nElegant preview...

The Logitech Z120 features an outer assembly designed using SolidWorks, a powerful CAD software that employs advanced surface modeling techniques to create a sleek and efficient design.

Z607 speaker likely identical to Z606 speaker, measured manually with vernier caliper due to curved surfaces visually estimated. Version 4 consists solely of the speaker unit, whereas version 9 adds a ceiling or corner component along with 2.5mm...

lost the grill for my center channel, made this in tinkercad. ...cover with thin black material like leggings knee high or speaker grill material

In order to mount it is advised to remove the legs of the speakers (You have to dissasemble the speakers and remove that screw and then place a screw in that hole in order to seal it). To mount this easily it is advised to place the cables in the...

To motivate myself to complete this project, I am sharing it now. ...Look forward to additional renders and the release of the model shortly. The speakers feature a simple Bluetooth design for wireless connectivity, with a fun and trendy appearance.

My was gifted these speakers about 10 years ago, but the person never included the one stand. ...I used it lying flat on table for all these years, until I realized this is the perfect use case for my printer.</p>

My Logitech speaker system never came with one of the feet for the bass unit so I designed a replacement in Solidworks. Enjoy! ... Instructions Use supports

My Logitech speaker system never came with one of the feet for the bass unit so I designed a replacement in Solidworks. ...Enjoy!