logitech unifying receiver replacement 3d models

 See the YouTube video for assembly hints; the idea is that the accessory thread adapters replace the nozzles so that you can use the accessory pipes instead.  2x Lock Collars, 2x 30-degree accessory adapters, 2x elbows, and the F-F...

Due to the design of the default loadout and hardpoints of the MWO Stalker, every initial gun the Mech is equipped with can easily be replaced with the respective weapon from the pack. During the moderation process, it was made sure that having...

For children, the colours should be appropriate for children. The clock face can be customized with the number cubes for practicing clock times.There are a total of 6 different ways to insert the cubes into the case, with the letters (AS TIME...

This way, the holes in the ring will show always the same number.So you can use the ring to generate random numbers or as a replacement for a 12-sided dice. Also it feels quite different to spin and creates a little rattling noise when...

This is my design of a toy meant to teach children about the effects of an inclined plane on a rope/pulley system and the forces involved.  There are 4 3D printed parts in total and 7 externally sourced common hardware materials.  OpenSCAD Source...

 Without this print your last option when struggling would be to remove the PTFE tube from the extruder and feed the filament directly into the extruder before replacing the tube. A minor annoyance at best, but constant disconnects chew up the end of...

I used a .15 layer height.• I designed Pins to replace the screws in places they don’t need screw tension and tend to fall out from the rotation. The pins have nuts to just latch in place. The 10mm short slots are probably best but a little harder to...

[](https://drive.google.com/uc?id=1miV9jUP1q0oJhb1ZlFa0LvnAmhT8P9M0) ### [Krechet class light cruiser](https://www.starfleet-museum.org/krechet.htm) The Krechet was a matter /...

just in case the original author decides to take it down for some reason.) https://www.thingiverse.com/thing:3579224The first 7 pieces replace parts in the original, so obviously dont print the originals of those. 8-11 are in addition to everything...

The top of the table (Part C) fits loosely enough that you should be able to remove and replace it to access the inside.Legs and feet: Part A x9, and either Part E x3 or Part F x3 Connect the leg rods in groups of three, screwing the small and closed...

So I just made a little mount that replaces the end cap on the feeder fits in there holding the feeder at a slight angle. That angle seems to have solved most of the jamming issues. In fact I switched back to 5v and while it did jam once going...

You'll notice that the original cube has been replaced with a new mesh consisting of several sub-objects. Now it's time to start working on the actual 3D model of our wrought fence. Select all of the sub-objects by pressing Ctrl+A, then navigate to...

thanks to "Replacement Coupler for Playmobil Trains, by af12689 Oct 30, 2017", which I have remixed and scaled down for N gauge use. I will be adding these in all the right places soon.(all done)</p> <p>I have been unhappy with the smoke stack, a bit...

Now add a lamp, snap on the shade and plug it all in. For MMU prints, I recommend using the "De Luxe/Grand Luxe/Gran Turismo Selector" (item https://www.thingiverse.com/thing:3608229 at thingieverse) and the replacement IR sensor holder...

Now you can hang/place your spool holder! Once the spool holder is assembled you only need to unscrew that one bottom collet to replace the filament spool. It should only take a few seconds!</p> <p><strong>Pro Tip:</strong> Is your spool holder's...

The internal volume of the tray is about 110x35x24mm (you will of course, need to slightly undersize), it uses a captive M3 nut and thumbscrew + latch for tool-less opening, and has a sling mount on the side that replaces the stock cap. A tray that...

I did not like the brown color and replaced that for Light blue. I don't spray everything with an airbrush and decided to make it slightly less difficult. I bought the Tamiya Color spray (i added the link, and went for TS-12, TS-15, TS-23, TS-26,...

It requires a hex nut and a screw M2.5Edited on 04/10/2022:Delta-P fan duct with LED lights and USB camera.The replacement of the original extruder with the improved Delta P duct and the addition of the LEDs are very well detailed by the original...

In the original (Stratego) version, there are two small lakes that provide a "do not enter" area near the center of the board - in my version, there is a Stargate that replaces these lakes (one on each team) that allows instant travel for your...

Also you might need to replace it with a new one if it breaks.The TailpieceThe tailpiece has to be very strong, so you should use the following settings:0.10 mm resolution4 perimeters16 solid layers on top, 14 solid layers on bottom100%...

5.27.21 UPDATE: Well, these units are still going strong on my machine -- although I have replaced the case fan motors once apiece on my two units. Fans with bearings are definitely the way to go. Anyway, I uploaded two new STLs -- one for a quite...

The LRM-10 missile launcher, Zeus-36 Autocannon as well as other armaments the Cyclops is equipped with are assembled in such a way that can be potentially replaced when the alternative Guns Pack for the Mech is released.The model is saved in STL...

In addition, defective parts can be easily exchanged or replaced. In terms of print resolution, I recommend printing all larger parts at 0.2mm and the smaller ones at 0.1mm. The required printing time also plays a crucial role here. The larger...

&nbsp;I originally had it enter through the top, but you could not easily change it while your kit-card was installed.The PLA will loosen under the pressure, using a tight pin will reduce a need to replace the pin. &nbsp;You can put a rivet in the...

The armament the Cataphract is equipped with is assembled in such a way that can be potentially replaced when the alternative Guns Pack for the Mech is released.The model is saved in STL files, a format supported by most 3D printers. All STL files...

Just worked very well for me in many projects and has the advantage, that you can get the LED out again much more easily in case you have to replace one.This is the order in which the LEDs have to be glued in to work with the provided code (the two...

The Replicape in there will (I was told) be replaced by a Revolve when those are available. Looking forward to more pictures and feedback from Bitraf members finishing and using the printer. UPDATE 7 Dec 2018: It's confirmed I will be building a...

There is an optional picatinny mount that can be used for sighting devices - this could be replaced by a simple aiming telescope if required, but this mount is very adaptable. Physical design - control box Note that the control box has been...

This release includes all the features from V3.1-beta 05/23/2023: Public Castle Preview - V3.1-beta - Corrected mistake in the documentation: "3x M3x8 screws" replaced by "3x M3x5 screws". This came from the Sorkin docs, they are too long. You can...

The Kumiko themed front panel is difficult to make with hand tools, however, a see-through front panel is not functionally necessary and can be replaced with the non see-through back panel.2mm Panel Mounting BracketFix the acrylic panel with these...