logitech streamcam tripod mount replacement 3d models
522141 3d models found related to logitech streamcam tripod mount replacement.
prusaprinters
Streamcam holder for tripod with joint.You need a threaded insert M3 (Ruthex) and a screw M3x18.The hole below is a core hole for 1/4 inch tripod thread.If necessary, I also have a lower part for the Ikea "Antifoni" lamp. Dismantle the lamp and mount...
thingiverse
Streamcam holder for tripod with joint. You need a threaded insert M3 (Ruthex) and a screw M3x18. The hole below is a core hole for 1/4 inch tripod thread. If necessary, I also have a lower part for the Ikea "Antifoni" lamp. Dismantle the lamp...
thingiverse
Mix of existing designs to mount Logitech StreamCam to the back of a computer screen.
prusaprinters
Logitech StreamCam GoPro MountSnap in place. ...Tight fit. Not for bike mounts or similar ^^'The lens cover in the pictures is this one: https://www.printables.com/de/model/283582-logitech-streamcam-lens-cover
thingiverse
# Logitech Streamcam bipod Use the original streamcam laptop mount as a desktop bipod ^^ Pass the mount through the shirt and slide the legs. Cam can tilt and pan, as if it was a neck. # Parts No screws, no magnet, slide in place. ... This is a...
thingiverse
Logitech StreamCam GoPro Mount Snap in place. Tight fit. ...Not for bike mounts or similar ^^' The lens cover in the pictures is this one: https://www.thingiverse.com/thing:4582384
thingiverse
A mount for Logitech StreamCam which is designed to support rotation of camera angle. ... Send me a message and I will also upload the free cad file FreeCad file are available on github: [Logi Stream Camera...
thingiverse
This is a piece for the modular **Modular Mounting System** by HeyVye, designed to hold a Logitech Streamcam, even if it can be used with any webcams as it use a camera standard screw. ... Here are the screws the design is based on: ...
thingiverse
Are you annoyed at your streamcam mount constantly falling off? Certainly was my problem so I designed a frame that you just simply "pop" onto your webcam and you can then easily attach it to pretty much anything with normal photo thread (6mm) or...
thingiverse
Mixed 2 other designs to come up with this - you can mount it using the system [here](https://www.thingiverse.com/thing:3147899/files) onto one of the [balls](https://cdn.thingiverse.com/assets/44/44/ed/fd/28/C920_Mount_-_Ball.stl) Works pretty well
thingiverse
Its a mount for a Streamcam and it replaces a Panelclip of my Voron 2.4. Works great but the Raspberry PI 3b+ only gets 10FPS out of it. worth a try on an rPi 4 though. ... Its designed for 2* m3 heatset inserts and a 1/4" Tripod Screw
prusaprinters
A simple mount for a Logitech Streamcam and the Ender S1.Can be printed on its side without the need for supports, with the exception of paint on supports for the cable holes.To attach to the body of the S1 I used M5 x 19mm screws.
thingiverse
This is a mount designed to replace the bulky/heavy mounting base on the Logitech C920 webcam, featuring a standard 1/4-20 tripod screw hole. There are two versions of this mount: a low profile version that sits approximately flush with the bottom...
prusaprinters
This is a mount with standard 1/4-20 tripod screw hole to replace the bulky/heavy mounting base on the Logitech C920 webcam. There are two versions of the mount: a low profile version which sits approximately flush with the bottom of the camera and...
thingiverse
Streamcam webcam mount with joint to fit on a 3/8" boom or microphone mountRemix of the Logitech Streamcam Tripod Mount with Joint by Neoz3dRebuilt from scratch in Autodesk Fusion 360 based on Neoz3d's design.Model is fully 3D printed. Replaced the...
pinshape
Easy to #3Dprint security cover for enhanced privacy with your handy Logitech StreamCam C980. No glue, just click the cover into the frame hinge and mount it on the camera. Easy to open, easy to stay close. ...Printed in cca 30–40 minutes with 0.15mm...
thingiverse
here's a nice little camera cover for a Logitech Streamcam, I used a small 1.5mm nail as the hinge. ...I printed mine using slightly flexible PLA
thingiverse
A slide-on lenscover with hinges made for the webcam StreamCam from Logitech. ... Printed in PLA with layer height 0,15mm.
thingiverse
English: This is a light protection for the Logitech Streamcam. It is designed to reduce incident light from above. It consists of two parts and is joined together with glue. German: Dies ist ein Lichtschutz für die Logitech Streamcam. Er soll...
myminifactory
Easy to #3Dprint security cover for enhanced privacy with your handy Logitech StreamCam C980. No glue, just click the cover into the frame hinge and mount it on the camera. Easy to open, easy to stay close. Printed in cca 30–40 minutes with 0.15mm...
thingiverse
Easy to #3Dprint security cover for enhanced privacy with your handy Logitech StreamCam C980. No glue, just click the cover into the frame hinge and mount it on the camera. Easy to open, easy to stay close. Printed in cca 30–40 minutes with 0.15mm...
thingiverse
The original clip for mounting Logitech webcams on their plastic stand is subpar; thus, this snap-in mount for tripods was designed as an alternative solution. It functions well and may be useful to others. Customize the STL or SCAD file by adjusting...
thingiverse
This is a simple adapter for the Logitech Streamcam, so that it can be mounted with a screw into a monitor wall mount. The ultrawide monitor (pictured) was too thick for the normal monitor stand in the middle of the monitor. This adapter just...
prusaprinters
This is a simple adapter for the Logitech Streamcam, so that it can be mounted with a screw into a monitor wall mount. The ultrawide monitor (pictured) was too thick for the normal monitor stand in the middle of the monitor. This adapter just holds...
prusaprinters
A two piece lens cover for the Logitech StreamCam.Use any bit of filament, 1.75 mm, as a pin for the hinge. Can be printed without support