logitech speaker wall mount 3d models
531181 3d models found related to logitech speaker wall mount.thingiverse
... to hang Logitech Z200 Speakers, probably works for the newer 207 series, haven't tried. ... Has recesses to allow for wall anchors. Links below to the products. * [Logitech Speakers](https://amzn.to/2RXlD7d) * [Wall Anchors](https://amzn.to/2W4DqIQ)
thingiverse
I was looking for a wall mount for my little Logitech Z313 speakers but no luck so I fired up the good old Fusion360 and designed this baby boy. ...It holds the speakers perfectly with a simple nail hammered in the wall.
thingiverse
I needed a support for my speakers (logitech z213) so I made a very simple but usefull one. ...I mounted it.
thingiverse
Its a wallmount for the Logitech Z213 Speaker and Subwoofer
thingiverse
... ones work better for me. (I didn't try his version) The screws needed for the speakers are: Pan head 1/4-20 x 1/2 UNC (per speaker 1 is needed) 2x wall screw depends on the socket you use (per mounting point) Feel free to contact me for questions!
thingiverse
The Wall Mounts leave the speakers perfectly vertical to have at ear level. ... center and other speakers Petg filament 0,2 mm resolution %100 infill No support
thingiverse
Hi, I needed a wall mount for my beloved Logitech Z623 speakers, so I created one. (!!!) Please note, I created the wall mount for the speaker without the buttons. Since that's the one I needed to mount to the wall. It could be that you want to...
thingiverse
Logitec creative speaker wall bracket to replace the original speaker stands. ...This allows them to be screwed into the wall.
thingiverse
This small hanger can get your Logitech Z200's off your desk and mounted up on the wall! I made the holes for #8 screws, and I put 2 screw holes in these hangers, but you'd be perfectly fine using just 1 up top The L & R hangers are angled at...
prusaprinters
I felt like I needed more room on my desk and figured I could make wall mounts for my Logitech Z333 speakers on the desk. The shelves came out great! You can use these shelves to hold other items as well. I added a picture of one holding a plant for...
thingiverse
Logitech Z906 speaker wall mount. ... including angle 0, 15, 30, 45, 60, 75
thingiverse
Made these to replace the factory foot on my Logitech THX speakers so I could mount them on the wall beside my monitor
thingiverse
Couldn't find a wall mount for the speaker system I had, so I made one.
thingiverse
Speakers were made to sit on a desk below eye level so they have a slant up to them. ...The Wall Mounts leave the speakers perfectly vertical to have at eye (ear) level. Also, they are friction fit. ...
thingiverse
Wall mount for Logitech Z906 speakers. ... Facebook page: https://m.facebook.com/story.php?story_fbid=195946021184417&id=128803144565372 Instagram: Printareprototipare3d
thingiverse
Flipped wall part screws Speaker part extended and tilted to 20° angle. ...Screw i used is 1/4-20 UNC, 25mm long thread with hexagon head of dimmensions side to side 11mm and 5mm height
thingiverse
You might wanna tweak the resolution to 110% according to the depth of the speaker itself. not sure what percentage is right, i just figured it out because the cable is pretty thick..... ... Tipp if you want to support my work
thingiverse
English : For my workbench, I wanted to install my Logitech Z323 speakers so I wouldn’t take up too much space. So I created this small shelf to put the speaker horizontally, fixed by 4 wood screws of 4*15mm (2 can be enough). To print the 2nd...
thingiverse
This is a wall-mount for an old set of speakers I had in my workroom - the logitech Z2300. It has keyhole cutouts to slide onto some 8G woodscrews. ... To use: - Print - Use the print to mark screw positions - Screw 8G woodscrews into the wall -...
thingiverse
I needed a wall mounting system for my Logitech G-51 surround sound speakers. ...This should work, now if only my hotend would quit jamming.
thingiverse
Screw Clamp adaptor to use M5 Screws instead the original one to adapt Logitech Speaker. ... Have fun!
prusaprinters
I wanted the satellite speakers wall mounted (I have no other place for them) I took advantage of the rectangle sort of sticking out the back, it also tapers getting ever so slightly wider as it goes in, this meant I could make simple box to...
thingiverse
To optimize the experience I decided to mount the speakers to the wall and designed these mounts to get the Speakers mounted efficiently and as close as possible to the wall. The screw diameter for the wall side is 3.5 mm and for the speaker...
thingiverse
... ...Its a remix of Logitech Speaker Wall Mount by ayapejian.. I changed it by making it screw into whatever is above it. There is a hole in the bottom to allow a screwdriver to reach the screw. ... Please let me know if you have any questions.
thingiverse
This is a Mount for a middle speaker for a logitech speaker setup. ...It uses number 6 size screws.
thingiverse
This is a speaker mount for the L&R speakers for the Logitech Z625 set. I designed it to be mounted with button head screws in the middle of a 2x4. ...There is a place to zip-tie the cord of the speaker to the mount.
thingiverse
This allows the Logitech Speaker Volume control (and headphone jack) to be mounted under the front edge of your desk. ... Access to all controls an ports are still available.
thingiverse
[NL] Om de audioweergave ervaring van mijn Logitech Z906 speakers te verbeteren heb ik een set van 2 modellen gemaakt om de speakers hoger t.o.v. mijn tv te plaatsen. Ze zijn gemaakt om op een Ikea KALLAX kast te passen. De buis is een gordijnroede...