logitech m570 trackball 3d models
7227 3d models found related to logitech m570 trackball.thingiverse
Lost one of the pads to a Logitech M570 after a clean/refurbish teardown. I suspect that The Blessed Cat is involved somehow but she claims innocence. Replacement printed from a sample of Ninjaflex and attached with a bit of double-sided...
thingiverse
Vertical (40 degree incline) mount for Logitech M570 Trackball 4 perimters and 10% infill sits securely
thingiverse
A 45° wedge stand to hold the Logitech M570 trackball mouse. Held in place via ball and battery holes. Place to store battery cover. ... Find ergonomics better than flat and takes up less space.
prusaprinters
A 45° wedge stand to hold the Logitech M570 trackball mouse. Held in place via ball and battery holes. Place to store battery cover. Find ergonomics better than flat and takes up less space. Print instructionsWedge print is hard plastic. No supports...
thingiverse
... The Logitech M570 trackball has a few underside features that allow it to be held in place from below. The battery cover plate must be removed to insert the unit into the holder. I also carved out a hole to store the plate so it doesn't get lost.
thingiverse
I Remixed Foxpup's mount to tweak a few things: 1. The base is now an extrusion of the outer vertices 2. I eliminated most of the lower brim save for the parts that contact the mouse 3. a few things have been resized for fitment The 45 degree...
thingiverse
[Durandal21's](https://www.thingiverse.com/Durandal21) excellent [Logitech Trackball Wedge](https://www.thingiverse.com/thing:4933557) is amazing, but I thought I could make it lighter and expose the power switch underneath. ... I drilled out...
thingiverse
Thanks to Tackleberry for the original from which this is remixed. It removes the tab on the rear of the mouse. I also added a 10 degree variant. ...The usb will not stay in the 10 degree version, but should function the same otherwise.
thingiverse
Got a wild hair...so you get the Punisher logo Will probably need support for the logo, don't think the angle is too great for the main body Just imported the .stl into tinkercad...scaled the logo, voila Make sure you go back to the original designer...
thingiverse
rsheldiii's 30 degree design but sliced in half for those with smaller printers. Added two slots for a tight fit. ...Glue if needed.
thingiverse
Ergonomic Trackball holder for the Logitech m570 at 45 degrees. I saw a few other models on Thingiverse but none were satisfactory, So as a practice I made this in Autodesk Inventor. It has has A holder for the battery cap. I printed this...
thingiverse
My kids lost the battery cover for my Logitech M570 trackball. First 3D thing I've designed. Careful not to break a tab when separating from raft. I printed with 50% fill and high resolution on my Replicator 2. ...Designed in SketchUp Make.
myminifactory
This voronoi ergonomic mouse stand for the Logitech M570 Trackball mouse lifts your wrist off the table and rotates your wrist for a more natural position. The model shown was printed on the Prusa i3 Mk2 using a 0.15 mm layer height. ...I put these grip...
thingiverse
This voronoi ergonomic mouse stand for the Logitech M570 Trackball mouse lifts your wrist off the table and rotates your wrist for a more natural position. The model shown was printed on the Prusa i3 Mk2 using a 0.15 mm layer height. ...I put these grip...
thingiverse
This is a simple 10 degree inclined riser for the Logitech M570 trackball mouse. I use a standing desk, which puts a strain on my wrist when using the mouse. This "thing" helps set the mouse at a healthier angle. The current version works well...
thingiverse
Si vous avez perdu un ou plusieurs plots de la souris trackball M570
thingiverse
I switched to a trackball (M570) and still found that the angle of my wrist to be sub-optimal. I created this 3D printed part to provide an almost 90 degree angle for my wrist. To my surprise, it works very well. The only issue is that you need to...
myminifactory
Did you somehow break or lose your Logitech M570 battery cover? Well I didn't. That is how I was able to design and print a backup cover! ...The included tolerance makes it easy for the cover to pop in and out, hassle free.
thingiverse
While looking for a source model of the mouse itself, I came across Dan Ellinwood's "Logitech M570 Stand" model on Onshape, where he had done an excellent job of extracting the m570's outline from a photo. I made a few tweaks, added in the receiver...
thingiverse
Trackballstand REMIX Natural Ergonomic Logitech M570 Trackball Stand Punisher by WarHawk8080
thingiverse
Mount for a Logitech M570 Wireless Trackball Mouse Two versions for either M5x16 or M6x16 bolts to Profile. ... Bolt holes are on a 20mm grid with the corners at 40mm Uses Velcro 3/4 Coins to hold the Mouse to the tray.
prusaprinters
Mount for a Logitech M570 Wireless Trackball Mouse Two versions for either M5x16 or M6x16 bolts to Profile. Bolt holes are on a 20mm grid with the corners at 40mm It uses Velcro 3/4 Coins to hold the mouse to the tray. ... The image is from another...
thingiverse
This is a form fitting trackball tray and support for the Logitech M570 Wireless Trackball Mouse and mounts to my SimLab PSE USB Wheel mount back. It uses M3 bolts and M3 threaded inserts as well as "VELCRO Brand - Sticky Back Hook and Loop...
thingiverse
Simple adjustable stand for a trackball mouse. Prints with no support. Allows to keep your hand in position of least strain. Both parts of the hinge are identical, you just print the STL twice. I used a couple zip ties for the hinge shaft, and a...
thingiverse
I'm currently using an MX Ergo (pictured, though it has the ball from an M570), and I sized this accordingly, but I'm fairly certain it should work for most if not all Logitech trackballs. Just scale it to fit if not. ... If you enjoy this design,...
prusaprinters
This is designed for a Logitech M575 Trackball Mouse. Others may work, but the contour in the part is shaped specifically for this mouse.</p><p>I've been incredibly busy at work recently and I've notice my mouse wrist has started to feel some...
thingiverse
mouse stand for logitech m575. ...helps keep a more confortable angle for your wrist.
thingiverse
I printed and tried this base: https://www.thingiverse.com/thing:5020749 and felt like it raised the trackball too much for me, so I decided to design my own with the following objectives: * Raise the low part of the trackball as little as possible...