logitech g920 with shifter and handbrake 3d models

Needed a web cam mount that was not restricted to only vertical up/down adjustments like the standard mount that comes with the Logitech C920 webcam. This is because I like to use two side by side monitors angled slightly. Thus mounting it on either...

This design enables users to interface a hydraulic handbrake with a computer and utilize it as an analog input for most sim-racing games. The files are specifically designed for the [LZONE-RACING Aluminum Universal Hydraulic Handbrake Lever Drift...

This is a remix from https://www.thingiverse.com/thing:398515

IMPORTANT:ball.stl needs to be glued to camera holder.socket-stick.stl needs to be glued to clamp.Can be mounted to anywhere which the clamp can fit.

Feet replacement for a Logitech K280e keyboard. ... This is a Remix from: Elías Rodriguez Martin

Feet replacement for a Logitech K280e keyboard. ... This is a Remix from: Elías Rodriguez Martin

Replaced the need for an M3 nut and bolt with a printed thread and nuts suitable for manually adjustment of the joint.The camera grip is tapered to fit the Streamcam body better, similar to the OEM grips. The base of the joint has a female 3/8" 16...

Remix : https://www.thingiverse.com/thing:4351501 Remixed this as I needed a holder for my Logitech F710 gamepad with battery holder which can be mounted with screws under my shelf - it can also be mounted under a table. I added some foam tape as...

Handbrake handle for universal hydraulic handbrake

#F1 Wheel for Logitech G920 There's already a version available for the Logitech G29, which can be found at https://www.thingiverse.com/thing:4177079. **Requirements** To build this F1 wheel, you'll need the following components: - 4 x M4x18 screws...

I added the logitech logo to the original design located here: https://www.thingiverse.com/thing:4968424

Remix : https://www.thingiverse.com/thing:4351501 Remixed this as I needed a holder for my Logitech F710 gamepad with battery holder which can be mounted with screws under my shelf - it can also be mounted under a table. I added some foam tape as...

I successfully printed it without support on a Prusa MK3S+ in Hatchbox PLA vertically, knob-up shaft down by adding a 10mm brim to prevent the part from popping loose from the print bed at 20% infill and all other settings default. Creative Commons...

A 50%+ infill setting and at least 1.2mm walls (three walls with a 0.4mm nozzle) on the clamp provide added strength. ...Supports are required on the clamp piece when printing on its side, but not on the spinner or cup, which should be printed with the...

This setup was designed specifically for use with the Handbrake Windows Racing Game and FANATEC OSW, after I had to replace the Micro controller. ...The combination of these components should enable users to create any AMStudio style handbrake by...

Based on this model I wanted to screw the holder in place. 

Filaments are a great choice for modeling - HIPS is one of my favorites! ...I'm really enthusiastic about using it with my ZX Spectrum emulator, it's such a nostalgic and fun experience.

Fuse for screw-in gearshift leg. ... Suitable for some models of Venzo, SLP, Raleigh and more.

Certainly, I can rewrite that sentence for you. ...Here's an alternative version with the same information but different wording: "Various components for minor engines."

A custom-built foot lever was created for my friend's motorbike, going through the stages of conceptualization, design, and production to achieve the final product.

MR148 bearings used in original design are hard to get localy and very expensive. I made minor modifications to use 687 bearings that are much more common and a lot cheaper. ... MR148 bearing dimensions are 8mm id / 14mm od / 4mm h 687 bearing...

... the keyboard. The 2 sides are in 2 different files. Only the right is shown in photo. I printed it with support and not only for the fun image it makes ! It takes less than 10 min to print at low speed. (Only 20 layers). ... Hope you enjoy.

... X ends, which have distinct dimensions that require a unique approach. I've got plans to modify it for standard MK3 use in the near future, but in the meantime, I'm sharing the Fusion 260 files with you, so feel free to customize them as needed.

Keyboards featuring macro keys, equipped with blue mechanical switches are available for purchase.

This is a redesign with most of the bumps removed so i can put the metal pedals on.

I was inspired by aluminum Logitech cases found at https://www.kurokesu.com/shop/KITC920, but also wanted to add some lighting features.\r\n\r\nOnline tutorials are available for completely disassembling your C920. ...Installing the camera into a 3D...

This thing is a replacement Hub Cap for the stock Logitech G29 Racing Wheel. Instead of the PlayStation Logo it now displays a TUX Penguin. This dimensions of this thing are as close as possible to the original. ...I've printed it on a SLA Printer.

... this one, https://amzn.to/3kjaIPo) as I noticed really annoying reflections when printing on glass! ... The inner hole is ~26mm and should accept most 24mm filters Also removed from https://www.thingiverse.com/thing:714475 (but wont let me add it!)

I've reworked the c270 camera holder and mounts for the MK3. The X axis mount is specifically for the Zaribo X ends which have slightly different dimensions. ...When I have a chance I'll make it work for the standard MK3 but I've included the fusion 260...

Redesigned the front cover to accept a circular polarizer (I used this one, https://amzn.to/3kjaIPo) as I noticed really annoying reflections when printing on glass! The inner hole is ~26mm and should accept most 24mm filters Also removed from...