logitech g920 magnetic shifter mod 3d models

The holes for the magnets are quite tight, so it's essential to use a 6mm drill to ream them out before inserting the magnets using a pair of pliers. To complete this project, you'll need the following parts: * Four neodymium magnets (each...

I needed a straightforward and adaptable way to support my timelapse C270 camera, so I created this simple mount using a neodimium magnet that was just lying around, measuring 12mm in diameter and 5mm in height. To secure the mount, I employed an M3...

I wanted a super simple and easy to change positions support for my timelapse C270 camera, so I made this easy support with a neodimium magnet I had lying around, diameter 12mm, height 5mm. I used an Allen M3 x16mm screw... Forced threaded in the...

Available in two variants, 6mm magnets for light actuation, and 8mm magnets for heavy actuation. Required Hardware: (4) 6 x 2mm disk magnets OR (4) 8 x 2mm disk magnets (4) M3 x 5mm countersunk screws Installation Instructions: Remove shifter...

Подставка для клавы Logitech

Neodym Magnets 15x4mm - 14-16x (depending if you want more magnets on shifter for stronger feel) 2. Omron micro switch or clone with straight handle - 4x: https://www.aliexpress.com/item/32273125391 3. M3 Standoffs (o.d. 5mm), 18mm long - 12x:...

this is the submarine ociangate controller

This lets you adjust the focus of your C270 without taking it apart.\nPost-Printing\nStep 1\n Remove the camera and loosen the lens. Research online for guidance if needed.\nWhile disassembled, take the plastic part (the one with...

Print the wheel with the shaft horizontally and with low layer heights, so it spins better. May still need some sanding to fit into the encoder. With my particular brand of PLA, I managed to get the whole thing down to 30.7 grams, your results may...

Here's a Simple throttle lever extension to make it more comfortable to use according to my preference. ...This design is inspired by the innovative CH Throttle Quadrant Throttle Knob created by AstarothReborn.

The Shifter boots are specifically designed to fit the G920 model.

Shifter for custom diecast / RC / slot / Model kit 1/24 Scale (Can be rescaled) 4,32 x 6,17 x 11,05 mm For commercial use of the files, contact me first Attention: -Take care when you remove the supports -Parts should be glued. ... -Not recommended for...

----------------------------------------------------- Check out all my Anet A8 projects: - Anet A8 Prusa i3 Simple filament guide (Horizontal) http://www.thingiverse.com/thing:1764285 - Anet A8 RPi Camera Bed mount...

Magnetic paddle mod for Thrustmaster TS-PC Racer Ferrari 488. ... I use 2 12x3mm neodinium magnets for each paddle.

... experience, with magnets placed diagonally for enhanced attachment. Additionally, the updated design allows magnets to slip in from the opposite side of screwing them on, preventing accidental detachment and sticking to their opposing magnet.

Introduction --------------------- Of course, there are several other Mag-Shifter Mods available out there, but one of the main issues I had with them is that they all relied on gluing magnets to plastic. Which I think is neither aesthetically...

Logitech's Extreme 3D Pro Joystick Takes Gaming to New Heights

With printed 3.5mm pads

IDEA: Enhance the experience by replacing tactile sensations with springs and metal balls, providing a more enjoyable feel and increased resistance to wear. To bring this idea to life, consider the following components: * 10mm Metal Balls (4 units)...

Just moded the "V2 top" with a "blocking-tab" for every gearbox in the game

Drawing on SolidWorks 2011.Print 3D: https://www.thingiverse.com/thing:1274947

This is a modification for the stock gear shift in a 3rd Gen (ZC32S) Suzuki Swift Sport (6 speed) that will improve the engagement of gears if yours has worn and become loose. NOTE - almost everyone will have worn shift cable bushings and those...

This converts your transaxle linkage to a thrust bearing design. Has been installed on our rally car for over a year and has been perfectly fine (printed in ABS - see more info in printer settings section). The "V2" version is recommended as it is...

I acquired a go-kart steering wheel, so I created enlarged shifters that I positioned closer to the steering wheel. Feel free to modify them for personal use or design purposes, but refrain from profiting from them. Drawing inspiration from these...

Saw a version made of aluminum with wire channels for personal use by @Junkyard_godz but was perplexed not to find that version included nor any remixes. I decided to take the kindly provided step file and carve the channels myself so here you go! ...

These two parts will allow you to add a magnetic paddle shifting mod to your CSL Elite ClubSport F1 steering wheel. Additional items needed: - 4x 8x3mm Neodymium Magnets - 4x M3x10 Screws - Super glue (optional but recommended) For added magnetic...

... magnets you have to glue. You can easily add more of them in the back side of the mod to change the effort. To complete the mod, you need: 4 magnets (gold 8) 8*3mm 2 double side adhesive tape Video: https://www.youtube.com/watch?v=t-ISTAyeyhE

Of course there are several other Mag-Shifter Mods out there, but one of the main issues i had with them: They all relied on glueing magnets to the plastic. Which i think is neither nice to look at, nor very long term stable. Since these parts are...

The idea is based on this video: https://youtu.be/mqSQhwqSzvg For assembly the mod you will need the following parts: Magnets: 5x2mm - 12 pieces 3 mm ball - 6 pieces 10x3mm - 4 pieces Screws: m3x10 - 2 pieces m3x5 - 2 pieces for Z screw holder you...

For assembly the mod you will need the following parts: Magnets: 5x2mm - 12 pieces 3 mm ball - 6 pieces 10x3mm - 4 pieces Screws: m3x10 - 2 pieces m3x5 - 2 pieces m3x15 - 4 pieces Nuts: m3 - 6 pieces for Z screw holder you will need: Bearing 628 -...