logitech g27 clamp 3d models

Take advantage of the screw of the original knob, screwing the adapter and on this same knob, It is recommended to use PETG although PLA can also be used If you want a specific model can be designed, do not hesitate to send me a message!

I designed two uncomplicated printing spacer options for users. ...The initial version completely replaces the original spacer, while the secondary option is an adjustable piece that can be installed beneath the existing spacer to customize pedal...

This ring mod can be installed without taking off the steering wheel. BOM 2 x M3x20-25 Cap Head Bolts 2 x M3 Nuts 4 x Ø6x2.5-3 axially magnetized magnets Secure the magnets firmly in place with superglue. Mount the ring on the wheel's hub and...

Rebuild of the original clamp addon for Logitech driving force GT. ...If you lost yours, or you need to replace them, you now have the model to print it.

My desk boasts a chamfered edge, forcing my Logitech G Driving Force shifter's clamps to struggle for a secure grip. ...To rectify this issue, these extensions were crafted to snugly fit onto the clamps and extend them outward, allowing for a safe and...

The original clamp of the Ball and Socket Webcam Mount for Logitech 270/310 broke almost instantly as I screwed it in. This led me to conclude that this design is fundamentally flawed, prone to breaking easily with minimal stress. To improve upon...

The stock clamp screws on these Logitech racing wheels leave you struggling for a good grip, making it difficult to bind them to the desk. Loosening the clamps after a racing session can be a real challenge. I created an alternative cap for the...

My desk has a chamfered edge so the clamps on my Logitech G Driving Force shifter didn't quite fit. ...These extensions are designed to loosely fit on and extend the clamps out and allow the shifter to be securely mounted to the desk without risking it...

People need assistance with optimizing DFGT settings for tighter clamp. ...Can we get some help?

I combined ClassicGOD's X52 Pro adapter dimensions and hardware with Aynareth's Thrustmaster T16000M FCS HOTAS Table Mount to create a mounting solution for the Logitech Saitek X52. ... ClassicGOD's pins were modified to have flats on both sides,...

I broke the clamp 2 years ago and created quick replacement, that broke down last week so I finally made a proper one

I broke the clamp 2 years ago and created quick replacement, that broke down last week so I finally made a proper one

I just made an extended version of this clamp because the top of my desk is thicker than the current clamp could reach I also modified the bolt head because I didn't like the knurl pattern when it printed you still need 2 for the yoke to mount

I use a corner desk which made using the default non-extended clamps impossible, as it simply wouldn't reach under my desk far enough to actually grip the desk. ...I printed the source extensions as a hopeful fix which did make it better, however I...

Desk clamp extenders for the Logitech G racing wheel (G920 / G29), complements my clamp extensions for the Driving Force Shifter https://www.thingiverse.com/thing:4285245

TPU

A small boot cap to grab the larger hole I cut in order to remove material so I could get it closer to the shifter base.

To utilize an M5 screw clamp adapter with your Logitech speaker, you'll need to substitute the existing screws with this new component. ...This modification will enable a seamless connection between the two devices.

Replacement clamp's thickness for Logitech Driving Force GT Useful to fix the steering wheel to thin desks I created two version for 1 cm and 2 cm (like the original) Enjoy :-)

secure phone mount for phones up to 160mm long and 16mm thick. ...requires 2x 10mm M3 bolts and nuts

Used the merged top and added hooks for rubber bands in order to have the option to convert it to sequential.

I printed Danid87's shifter (2549977) but the screw collar broke really quickly and the shifter kept spinning around. I wanted it to be screwed directly into the shaft. There is a 2 layer bridge inside so will need to use a 4mm drill bit to open...

I've Remixed the Stl file of AntonyArt ( https://www.thingiverse.com/thing:4302821 ) Please download following things there: "Main_New_v2" "Inner_Ring_v2" I improved the H-Pattern, due to the original breaking too often. My Design releases...

I've created a handbrake that requires zero modifications to your gear selector. Simply print out the left or right base plate and snap it into place under the selector. I'm still refining the design, but this is a working concept for anyone...

Easy to install without any modification on steering wheels or the wheel base. It gives You very powerful and exact shifting feeling. Designed for 4pcs 8x5mm N48 Neodynium magnets and M3x16mm bolts with 2pcs M3 washer and 1pc M3 locknut. NO SUPPORT...

Customized version of https://www.thingiverse.com/thing:2367305 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2367305

Customized version of https://www.thingiverse.com/thing:2367305 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2367305

This is a remix (or maybe a complete make over) of the awesome stand made by AndrewFX (https://www.thingiverse.com/thing:2367305). I use it to house my phone so I can use the Smooth Track app to have a head tracker. As a bonus, it charges the phone...