logitech g13 3d models

Although this is designed to work with my Logitech C270, you should be able to mount nearly any camera to this mount. You'll need some M3 hardware and four 8 x 3 mm magnets. (Mine measured 2.67 mm thick.) First make sure your magnets will fit, then...

Here's my support model for Logitech C920, which sits directly on the board. It's not perfect because it's not compatible with all printers and I don't want to overheat the board. However, I couldn't find a suitable alternative for my printer...

It's also recommended to go with the Logitech C535, which works seamlessly alongside Octoprint or Octopi on Raspberry Pi 2 B+. The device allows for precise focus up close, as low as 7cm - this is not something that generally applies to less...

I currently use my Logitech C310, but this design should work seamlessly with any similar webcams that can hang from or balance on the edge of your laptop screen. This design is completely parametric and built in OpenSCAD, which makes it easy to...

UPDATE: I'm going to leave this thing up, in case it's useful to others, but I'm probably not going to use it for my webcam, as my Logitech C310 has too narrow a field of view to capture the whole build area when mounted on this. Might work for a...

The camera used in this setup is the Logitech C270, which has been modified with a mod that can be found at https://www.thingiverse.com/thing:3087454. The lens kit used in conjunction with this mod is also accessible via this link. ...The articulating...

The hook is shorter and rounded to fit the thin band of a Logitech H390 USB headset. This design is made to fit the 3M Command Strip adhesive strip, width wise, but you will need to trim off ~ 3-4 mm to match the 15mm arm depth. One can also use...

The smaller version of this mount is designed for use with the Logitech C920 camera and converts its M6 screw to an M6/camera screw. I created this design after accidentally breaking the original mount off my camera, leaving a large hole in the...

I made a microphone holder for my desk using the following projects: Unfortunately, I cannot get the remix source files to work in the UI to mark this a remix of the other projects, so here they all are: mountable arm microphone holder pop filter ...

This was made as a proof of concept replacement for the Logitech G29/G920 steering wheel as I wanted a rim that I could have an easier time reaching all the buttons. Yes the faceplate is made out of wood, it's was what I had laying around that would...

This camera mount is compatible with any camera featuring a standard 1/4" tripod mount, but it was specifically designed to work with my Logitech C615. When used with the C615 (or other cameras that have multiple swivel points), this mount can be...

http://www.thingiverse.com/thing:2325641 is the blueprint I used for my Logitech Webcam.\r\nAt my workplace, we have a Microsoft Webcam attached to a Taz, so I'm creating a version 2 design.\r\n\r\nThe Microsoft Webcam mounting system differs from...

This is a multi part print to easily attach a Logitech C270 camera to a Creality CR-6SE and be able to adjust it to how you want to view your print.It consists of a number of parts. MachineMount - This attaches to stepper motor and provides a stable...

HillbillyZT's mount wouldn't work with the Z brace mod, so I designed my own. This is compatible with any camera that has a standard 1/4" tripod mount, but I specifically designed it to work with my Logitech C615. When used with the C615 (or any...

(Please refer to attached images for clarification.)\r\n\r\nTo ensure stability, consider tapping M5 into the bed carrier; if not done so, the mount may come loose over time.\r\n\r\nPair this mount with...

To remove the original weighted Logitech mount from the camera, use a thin knife to carefully pry off the covers over the ends of the hinge pin. This will allow you to utilize a screwdriver to remove the pin. If necessary, apply gentle pressure with...

Since the STL files that are being provided were specifically designed for use with Logitech Pro 9000 and C270 webcams, as well as Prusa 1 and Rostock printers, this build is less of a finished product and more of a base template. As such, you'll...

Required Components: - 8 T slot nuts and bolts - 1 M8x10mm bolt - 2 M8x25mm (laser holder mount) - 4 M3x12mm(step motor mount) - 2 M3x12mm+nut (Laser fixing) Parts List: Electronics: - Logitech C270 camera - Arduino board - ZUM Shield - Red line...

Logitech G29 quick-release mod for interchangeable wheel rims. This is a non-destructive mod (you're able to return your G29 to its original state) but modify your wheelbase at your own risk, it will definitely void your wheels warranty. There are a...

I have added two designs for Webcams: one for a Fisch Eye / Wide angle Raspberry Pi camera one for a Logitech E35 camera If you have another camera; you can easily design a fixture yourself, a plain support design is included as a starter. The...

Hey, this is my first upload here on Thingiverse :D I'm excited to share with you a camera-mount design that attaches the Logitech C270 webcam to my Anycubic I3 Mega 3D printer. It's been a fun project, and I'm eager to hear your feedback! Edit...

Ok, so as I said in my previous upload (55mm Trackball), I'm not suggesting you go out and buy a Kensington Orbit, Adesso iMouse or Logitech Trackman Marble Mouse just to get a 40mm trackball to use with this system. That wouldn't make sense as you...

FAQ: http://www.thingiverse.com/shivinteger/about Generating Attributions log: Thing Title : Customizable Car Visor Sun Shade Thing URL : http://www.thingiverse.com/thing:2641 Thing Author : laserjockey Thing Licence : Non-Commercial - Share Alike...

I loved the original clip- but the camera mount doesn't work with the QuickCam Pro For Notebooks, which Logitech gave me a few years ago. I simply added a mounting bolt and wingnut (initially created with https://www.thingiverse.com/thing:193647),...

The ears only need a short length of 3/4" double sided Velcro tape [Like This](https://www.amazon.com/VELCRO-Brand-ONE-WRAP-Double-Sided-Multi-Purpose/dp/B000078CUB/) (About 4 3/4" (120mm) for a pair of Logitech G Pro headphones). NOTE: This Velcro...

This model is completely 3D printable but I highly recommend to make the baseplate out of 4mm aluminum, especially on machines which produce more torque than a Logitech Wheel. The inner design of the upper housing gives you the possibility to...

You can also check out my other sim racing products on cults3d.com by visiting the following links: https://cults3d.com/en/3d-model/various/thrustmaster-t500rs-steering-wheel-adapters-70-mm-and-74-mm;...

I loved the strong 'Ultimate Sturdy Octoprint / Pi Camera Mount' arm from Stewpercharged (https://www.thingiverse.com/thing:3374914), but I didn't want to mount a Pi Cam (using the 'Mendel90 Raspberry Pi cam holder' from JakesterDS —...

Top Plug This fits in to block off the Logitech camera location at the top of the Ciclop camera tower. This piece is a work-in-progress, destined to become part of the camera Raspberry Pi camera mount for the factory Ciclop tower. Motor Tube...

The project requires a Logitech C270 webcam, 5mW focusable red line laser, NEMA 17 stepper motor (max body length 36mm), A4988 stepper motor driver module, Arduino Uno, NKC electronics protoshield kit, a 1A 12V power supply, Elmers black foam board,...