logitech cameras 3d models

I needed a straightforward and adaptable way to support my timelapse C270 camera, so I created this simple mount using a neodimium magnet that was just lying around, measuring 12mm in diameter and 5mm in height. To secure the mount, I employed an M3...

... C920 base is a little wider. ... Factory screws hold this in place, although I did notice a slight spread apart where it attaches to the printer. Just added a new version, more rigid and a change in the placement of the camera for a better angle.

You will need one M3x30 screw to fix the camera to the mount.Print the mount laying flat on the side.Print the screws vertically.Threads are fine because of the limited thickness of the mount in order not to interfere with the idler below the bed.

I wanted to place my camera on the HP Dual Monitor stand's pole so it was centered rather then placing on one or the other monitor. Also prevented it from blocking any part of the screen. ... The pole measures 33 mm in diameter so if you have...

I wanted a super simple and easy to change positions support for my timelapse C270 camera, so I made this easy support with a neodimium magnet I had lying around, diameter 12mm, height 5mm. I used an Allen M3 x16mm screw... Forced threaded in the...

I redesigned the C170 camera mount from Thing 2288272 and integrated a LED strip holder. I utilized this LED strip: https://www.amazon.com/dp/B0152HO7K4, allowing for 5 sections of 3 LEDs each to fit within the holder. ...The design accommodates any...

Hey, I encountered an issue with the original mount not being stiff enough to hold the camera perfectly horizontal. To resolve this, I added another peg for the existing hole on the Z gantry so it can no longer move. The fit was spot on for me.

I crafted tough mounting blocks for my heat bed and an adapter for the C270 camera mount that I discovered on Thingiverse. To avoid any issues with melting, I highly suggest printing them in ABS plastic. I utilize a BLTouch sensor, and if you're...

Attach a C270 camera to a wall with ease. Remove the screw that secures the head to the bracket, then carefully pull out the pin. Retain this pin for later use. Next, insert the retained pin into the mount found in the attached file. To assemble...

To assemble the frame mount, extension(s), and camera mount, use M2,5 x 20 screws/nuts (available at Amazon under B015A338TG). For securing the USB cable, I prefer to use ZIP ties, planning to add some additional lugs in a future update. ... January...

I couldn't find a sturdy camera mount for the FLSun i3, 2017 edition, that didn't wobble and shake while streaming and capturing timelapses. I built a solid one that uses existing holes for slider bearing blocks. The clip also provides extra...

Print Settings: Printer: Mp Mini Select Rafts: No Supports: No Resolution: 0.2 Infill: 30% Notes: To achieve a better fit on the camera's lens, scale the focus ring to 98 or 99%. ...Additionally, double-check that the "tripod arms" are flat on the bed...

... stable. Also I added a ball joint so the view can be leveled if needed. Version 3 arm and base has some extra mounting points so the camera is more stable. ... Update 07/25/2019 - Added a custom housing in case you want to replace your stock one.

For more in-depth details on this innovative upgrade, check out my latest YouTube Video here: https://youtu.be/LklRBZ5ho-c You can also find comprehensive instructions and guides on how to implement this modification on my website:...

I wanted something that attached directly to the gantry or frame, so I designed thehalf-in_emt_camera_mount andhalf-in_emt_mount2 to interface with parts designed by luc_e. The minimum files are included in this thing with additional features by...

Since I wanted a solid attachment directly to the gantry or frame, I designed the **half-in_emt_camera_mount** and **half-in_emt_mount2** to seamlessly integrate with luc_e's parts. The minimum files required are included in this thing, along with...

This is a customized rendition of the original Logitech C270 camera mount designed by Jason3030. ... To suit my personal preference, I adjusted the camera arm downward to optimize the viewing angle.

I'm using a Logitech C270 camera mounted on an X-Axis Belt Tensioner, designed and manufactured by WedgeSD. ...You can find more information about this project at https://www.thingiverse.com/thing:1921667.

This combo X-Axis Tensioner and Camera mount is specifically designed for use with a Logitech C270 camera. To assemble, you'll need two M3 nuts, one M3x10mm cap screw, one M3x20mm cap screw, and two M3 washers if desired. ...The camera will be mounted...

Simple combination of the Logitech C270 camera mount remixed lower by martsl, and the X-Motor Cable Strain Relief by mdkendall. I literally just spliced these two models together. To print the single part version, you will need to add supports. ... A...

Support for Logitech C270 camera on X-axis for Creality Ender 3 S1 and S1 Pro printers. I made this support because I've tried others several times and I never thought they were good. This one best suited my needs. In the photos, you will see...

Für die Halterung brauch man ein M3 Gewindeeinsatz. Zusätzlich kann man ein 14x4mm großen Magnet einkleben und die Kamera-Leitung mit 5 Kabelbinder befestigen. ...

I created this guide to provide a clear pathway for the layer fan in the Tornado. To enhance stability, I modified the magnetic support by installing two neodymium magnets. Each magnet measures 12mm in diameter and 5mm in height. Use an M3 x16mm...

I'm searching for a hinged mount similar to caracarn's design, with one key difference: I only need to secure it on one axis. The .1mm layers kept shifting, but I found that increasing them to .2mm stabilized the structure. ...An M3x30 or M3x35 screw...

This is a custom mount for a CR10 or any 2020 frame that expands on the outstanding design of Luc_E's [C270 Tripod](https://www.thingiverse.com/thing:1228521). ...On the CR-10, it enables the tripod to extend from below the bed pulley system.

I was looking for a solution to securely attach my webcam for Octolapse compatibility, but couldn't find any suitable options for the Thinker S model. So, I created this makeshift mounting system as a temporary fix. ...Please note that additional...

I made this support to get a clear path for the layer fan in the Tornado. I modded the magnetic support with, now, two neodimium magnets for stability. Magnets are 12mm diameter and 5mm height. Use an Allen M3 x16mm screw, force thread in the same...

<p>I"ve adjusted the orginal design to fit my IKEA Platsa enclosure.<br/> The IKEA Platsa panels have predrilled holes every 2,5cm. So I've adjusted the magnetic wall plate to fit the PLATSA predrilled holes.<br/> I used 6mm x 3mm magnets because...

No need to reinvent the wheel, the original works really well but didn't sit well on my Ender 6 so I remade the base. My C270 now sits nicely on the back of my printer with this mount sitting on top of the extrusion. I printed it with 80%...