logitech c270 wide angle 3d models

 You can also adjust the threshold angle which determines the crossover point between traditional and scarf seams.  In my pot tests and optimized settings, I use a value of 115 to force the scarf seam on everywhere for testing reasons.  This may or...

I used an angle grinder with a metal cutting disk. I kept the plastic wrap on the rail to keep shavings out of the bearing.I recommend replacing the rubber stops on the rails with screws to ensure the guides don't slide off during assembly.Make sure...

a speed bevel to mark or measure angles quickly. more tools will be included in the final set. i hope that they enable people who are starting off in 3d printing and design to be able to have a precision tool set that is adequate for design and...

Correct the angle of the potentiometer_gear, so that it moves together with the rod_gear and doesn't block it from moving the whole range of the pedal.Disconnect the pedal from the rod connectors, and tighten the potentiometer_holder screws:  ...

Note the treads match in shape the body of the Freight Ten.Superglue the cab superstructure to the body to the front grill is overhanging the front slightly (see the images).No print supports are needed.Superglue works best for gluing it together.Did...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version.Currently set at 75% size to reduce build time. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

While cutting periodically check the alignment of the two cuts and adjust the cutting angle as needed. Go slowly; it usually takes maybe 100 strokes to cut through a 1.6 mm board. For fine-tuning measurements one can place a shim between the...

... too tight and would not move one bit. The slot for the phone stand was too small and would hold phones at too steep of an angle. Seeing the overall shape of the pencil holder in front of me led me to make some additional aesthetic changes. ...

https://www.prusaprinters.org/prints/132133-machina-robot-model-v3 Also great for use to guard your Armoured Shelter ( https://www.prusaprinters.org/prints/121033-armoured-shelter-terrain-two-models ) Lol!Designed on Tinkercad.Four parts to...

The needle should retract fully into the guide on the upstroke. I sharpen the needle by removing it from the cutter and rotating it in my fingers while holding it against a cutoff disc in a dremel at a sharp angle. It doesn't take much and even a...

Slip the gloves onto the arms as far as they will go (about halfway, indicated by yellow circle). Angle the gloves appropriately. The circular patch on the LEFT glove should point slightly backwards, and the RIGHT glove should point slightly...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction...

Note the treads match in shape the body of the Freight Ten.Superglue the cab to the body to the front grill is overhanging the front slightly (see the images).No print supports are needed.Superglue works best for gluing it together.Did not use...

The STL filenames have the inner diameter in mm in the filename. In case you need even more different sizes, please install OpenSCAD on your own computer and follow these instructions to customize your ring.Using the ringsSo measure the diameter...

They can however be minimized by using a low density (10%), high overhang angle (>70%), and simple pattern like "Lines". The Electronics Base needs the most and will be hardest to clean, but using minimal supports will make it much easier. *...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version.Currently set at 75% size to reduce build time. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

Now with the Gen2's rail design you can quickly swap the storage units between work areas.Download the GEN2 Interactive Catalog PDFFeatures:• Gen2 rails allowing quick and easier swap-ability and combinations of many Gen2 Storage System designs.•...

Press firmly with screwdriver to ensure it is fully seated. Slide the Carriage Clamp Arm onto the front right arm of the Y carriage. Insert the M3 x 30 mm screw through the hole on the front clamp wing into the nut at the rear and tighten. Assemble...

The internal collar has 7 small notches around the perimeter, these are to line up the small gears around the body; the gears need to be both evenly spaced and at matching angles for the mechanism to work properly. I find it easiest to take each...

Press firmly with screwdriver to ensure it is fully seated.Slide the Carriage Clamp Arm onto the front right arm of the Y carriage.Insert the M3 x 30 mm screw through the hole on the front clamp wing into the nut at the rear and tighten. Assemble the...

Ready to pump your promethium, sweet crude, or whatever lights up your day!Designed on Tinkercad.Enforced supports are required on verticle pipes (see files).Superglue the valve handles.Start pumping that...

This way the holes should print closer to the desired dimensions, as polygon holes tend to print more accurately then circles.The back plate is secured with little pieces of 3D printing filament, acting as rivets: Cut the end off of the filament...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.  I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to...

- A10M fan duct wing (regular and angled) (https://www.thingiverse.com/thing:3522470) - A10M / A10 fan duct wing for radial fan 50x50 (https://www.thingiverse.com/thing:3585978) - Base cover to protect the cable from electronic box to the display:...

The second possible troublemaker is the space between letters; check that there are no holes, and adjust fill angle, or extrusion widths, or detect thin walls, etc., to fix any; don't rely much on bridging, as it will be too high to show in the first...

Take what's theirs and make it your own! More Armour!Demolior Class Heavy Tank - https://www.printables.com/model/135967-tank-demolior-class-heavy-deathhead-ii-model-scien Scopulus Class Heavy Tank -...

Place the Plunger, withthe hole in the shaft facing upwards, into the central shaft on top of the spring. Prepare 6 of the RimTabs by pushing a peice of filament through the hole and cutting it such that there is a bit less than 2mm of filament...

For this project the right angle headers for connecting the IR sensor to the board are not use. The IR sensor is connected to the board with a length of 3 conductor wire solderd directly to the board. This is due to limited space. There are 2...

I printed them at 20mm (4 hours or so,) but they look even better at 15mm.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...