logitech c200 3d models

This mount is compatible with any standard 1/4" tripod-mounted cameras, but I specifically created it to work well with my Logitech C615. When used with the C615 (or other cameras having multiple swivel points), this mount can be utilized for either...

To remove the original weighted Logitech mount from the camera, use a thin knife to carefully pry off the covers over the ends of the hinge pin. This will allow you to utilize a screwdriver to remove the pin. If necessary, apply gentle pressure with...

(Please refer to attached images for clarification.)\r\n\r\nTo ensure stability, consider tapping M5 into the bed carrier; if not done so, the mount may come loose over time.\r\n\r\nPair this mount with...

It works seamlessly with a Smart Cover or the Logitech UltraThin Keyboard Cover, and tilts to any desired angle. Additional details can be found on the blog: http://interlockroc.org/2013/01/ipad-handlestand/. Instructions Parts list: -(1) Hinge...

Thing URL : http://www.thingiverse.com/thing:15957 Thing Author : uck Thing Licence : Attribution - Non-Commercial - Share Alike Thing Title : Commodore Vic-20 Cartridge Case Thing URL : http://www.thingiverse.com/thing:52655 Thing Author : CNK Thing...

The camera used in this setup is the Logitech C270, which has been modified with a mod that can be found at https://www.thingiverse.com/thing:3087454. The lens kit used in conjunction with this mod is also accessible via this link. ...The articulating...

I'am proud to present my own fingertip GT1P shell creation for Logitech G Pro X Superlight 1 and 2 internals.GT1P by ㄷㅇㅇㄴㅆㅇㅁㄹ Thanks to tyuhn and ii999 for the inspirations.The clicks you can print with flat round holes or without. In the holes will...

I really liked @raveious' "Interior Webcam Mount" -- a rail and camera mount designed for the Makerbot Replicator 2 and the Logitech C270 webcam -- but wanted to adapt it to be used on other printers. What I ended up doing is creating a few different...

Great Robin 3D Printer https://youtu.be/5MfGsM_MGTk Original source: https://github.com/dherrendoerfer/The-Robin-3D-Printer-Project/tree/master/STL-Files/Bad-Robin Original Bad Robin 3D Printer https://www.youtube.com/watch?v=5juObRKD8EM&t=80s Bad...

I am in the process of making a mechanical mod to the Logitech G13 based on a previous mechanical mod. I wasn't a fan of hacking up the original or the spaghetti mess of wiring so I made a new keycap plate and pcb. I haven't ordered the PCB yet but...

I also separated the coupling from the shoe so other kinds of shoe can be made.UPDATE:Adjusted coupling length&height and added optional flexible padding for better stability.Adjusted foot to fit better.UPDATE 2:Changed coupling to better fit the...

Mount works on a [Logitech C920-style](https://amzn.to/3aLuoJ2) HD Webcam, but can be adapted to fit others. ## Bill of Materials - [Circuit Playground Bluefruit](https://www.adafruit.com/product/4333) - [NeoPixel Ring - 24 x 5050 RGBW LEDs...

This is my design for an ergonomic mouse shape using the Logitech G305 PCB. As this was my first attempt at designing something for 3D printing, the actual files I printed (Top and Base) are not perfect and some sanding is required to make all the...

I'm currently using this with a Logitech gamepad and a trackball I put together (https://www.thingiverse.com/thing:5441064). I've included a couple keycaps for the 7mm buttons. ...These are totally optional if you'd prefer to label the case instead.

This is the V5 Magnetic Shifters for Thrustmaster and Logitech 70mm Hub adaptors. What's in the kit? 1 x Mech plate with left and right mounting points 1 x LR Shifter Arm with mounting hole for paddles 1 x LR Shifter Arm stubby with 3mm holes for...

Parts: Bolts and nuts: M2.5: -4 x Button 10mm long screw M3: -4 x Button 20mm long screw -4 x Nuts M4: -4 x Flat 16mm long screw -4 x Button 20mm long screw -14 x Button 16mm long screw -2 x Button 12mm long screw -24 x Nuts M5: -6 x Button or Flat...

Blue Pill STM32 C8T6 - https://cutt.ly/hOSIzF6 Arduino Pro Micro - https://cutt.ly/nI141Yt 3 x Rotary EC11 15mm long - https://cutt.ly/fOSYVtB or 3 x Bourns PEC11R-4215F-S0012 - https://cutt.ly/pGlU76L or 3 x Bourns PEC11R-4215F-N0012 -...

This is a custom designed shell for the Logitech G305 wireless mouse. The total weight of the parts will be approximately 20g, depending on print settings and material, excluding the PCB, buttons or battery. It accommodates a standard AAA battery and...

NIFE – Piper PA-28 Cherokee / Piper Warrior https://www.thingiverse.com/thing:5142974 Primary / VT-6 “Shooters”– T-6 Texan II https://www.thingiverse.com/thing:5142965 Intermediate HT-8 “Eight Ballers” – TH-57B / Bell 206 Jet Ranger...

Night photos are a comparison of the low light performance I can get out of a Logitech c270 vs the IMX291 camera module. Photo of the moon were taken with guvcview. Scope was at about 42x zoom. Exposure was turned down nearly all the way, gain and...

Logitech C270 mount designed specifically for FlashForge Creator Pro and similar 3D printers, thoroughly tested on the FFCP. This design was a game-changer because it allowed me to position my camera just like I'm actually watching it. Plus, someone...

Materials needed: Aluminium tube Ø12 x 350 mm x2 Aluminium tube Ø12 x 105 mm x2 Aluminium tube Ø12 x 145 mm x2 Acrylic platform Ø200 x 3 mm x1 Acrylic pattern holder 160 x 100 x 3 mm x1 Logitech C270 camera x1 NEMA 17 Motor 28 mm height x1 UNO Board...

It can be mounted pointing in or out, in any available hole in either Y bridge.I've included a couple of simple box-shaped adapters that will hold a Logitech C270. One takes a 1/4" brass insert, and the other will mount directly to a Y bridge using...

The project requires a Logitech C270 webcam, 5mW focusable red line laser, NEMA 17 stepper motor (max body length 36mm), A4988 stepper motor driver module, Arduino Uno, NKC electronics protoshield kit, a 1A 12V power supply, Elmers black foam board,...

I used the Camera Mount for Logitech C270 on 2020 Extrusion by NikNolte on Thingiverse: https://www.thingiverse.com/thing:2426231 as reference for creating the base brackets to tilt the camera to my liking. The mount itself is completely custom. ...

Required Tools and Supplies: T20 Torx screwdriver Webcam - We used a Logitech C615: http://amzn.to/B004YW7WCY 1 3/4" long 1/4-20 bolt with 7/16" hex head 1 USB extension - We had to extend the C615 USB cable: http://amzn.to/B00NH11R3I 2 Small pieces...

...LED strip, cable management, etc.. Besides a number of mods such as a modular control panel with RPI4 & Waveshare 5" DSI, LED lights, Logitech 930c webcam, motherboard and PSU cooling controlled by a relay, this box has non-common features.

Ok, so as I said in my previous upload (55mm Trackball), I'm not suggesting you go out and buy a Kensington Orbit, Adesso iMouse or Logitech Trackman Marble Mouse just to get a 40mm trackball to use with this system. That wouldn't make sense as you...

You can find these parts on Thingiverse: **Magnetic Paddleshift Shifters for Simracing (Logitech)** by dankart27 https://www.thingiverse.com/thing:2724966 **Thrustmaster T500, TX, T300 Wheel Adapter** by Slowly...

Ok, so as I said in my previous upload (55mm Trackball), I'm not suggesting you go out and buy a Kensington Orbit, Adesso iMouse or Logitech Trackman Marble Mouse just to get a 40mm trackball to use with this system. That wouldn't make sense as you...