logi webcam c270 3d models

webcam logi c270 wall mount

Mi primer diseño. ...Fue para solucionar que la webcam apoyada directo sobre el monitor tapaba un poco la imagen. Falta algunos ajustes, pero así como está sirve. ... Es necesario dos tornillos VESA M4 para sujetarlo al monitor.

A minimalist Logitech Webcam Logi C270 Privacy Lens cover. ...Some colleagues at the Office requested this ;-)

Logitech webcam cover for C505 ( probably also for C270 ). Cover consists of 3 parts. Glue is not needed, but can be used if you like. The cover covers the lens and the mic, but not the LED so when the cover is closed you still can see if the...

Wanted to mount my webcam between my two monitors at my eye line rather than above/below. Simple design allows for adjustment on two planes after it is stuck to the back on the monitor. My monitor has a sloped back, hence the angle on the arm. A...

Wanted to mount my webcam between my two monitors at my eye line rather than above/below. Simple design allows for adjustment on two planes after it is stuck to the back on the monitor. My monitor has a sloped back, hence the angle on the arm. A...

Simple design allows for adjustment on two planes after it is stuck to the back on the monitor. My monitor has a sloped back, hence the angle on the arm. A small nut and bolt required to attache it to the webcam. ...(looked through my spares tub, unsure...

Snug slip-over privacy cover for Logi C270 webcam.

Snug slip-over privacy cover for Logi C270 webcam. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 mm Infill: 15% Filament: Generic PLA Silver Notes: Approximately 7.5g filament / 30 minute print...

... make the holes a bit wider. In case it’s too wide, just bend the paper clip in a wave form. Add double sided tape on the back side of the mounting plate but take care to not cover the holes. Place it on your Logi C270 WebCam.  

Mount to hold webcam on my shelves, screws down so it wont fall.

This is a case for a Logitech C270 Webcam, ready for a M12 bayonet lens.You will need an C270 webcam, 4 screws from it, M12 lens of your choise (i chosed ultrawide IR), couple of 10x5 magnets and a nut (or two) for joint.PS: Avoid printing from...

This assembly requires nothing more than your C270; no extra hardware is needed as I've adapted the design to use the original bolts. ...To enable manual focus, you'll need to remove the glue holding the adjuster in place - simply search online for...

Here´s a adapter for a webcam C270 for GoPro mounts. ...With an example for what I used it.

Freestanding Logitech C270 WebCam Holder ------------------------------------------------------------ I have multiple printers (3 different makes/model/sizes) whereas I needed to come up with a "One-Design" fits all design for use with the Logitech...

Eine Webcam Befestigung für die Logitech C270 Webcam.Es wird keine weitere Schraube benötigt!Erstellt fürhttps://www.printables.com/de/model/3407-articulating-raspberry-pi-camera-mount-for-prusa-mDie auf den Bildern verwendete Befestigung für den Cam...

Computer Webcam

Stand for a C270 Logitech WebCam Print Settings Printer: Prusa i3 Rework 1.5 by EMotionTech Rafts: You can use any type of raft you want Supports: None needed Resolution: Extremely fine at 0.15 mm Infill: The default setting is 20% but you can change...

This camera mount is designed for the Logitech C270 Webcam, which attaches to the Kingroon KP5L on the side of the existing filament sensor. You can reuse the two screws from the filament sensor to attach the webcam holder. The only additional...

Eine Webcam Befestigung für die Logitech C270 Webcam.Es wird keine weitere Schraube benötigt!Erstellt fürhttps://www.printables.com/de/model/3407-articulating-raspberry-pi-camera-mount-for-prusa-mDie auf den Bildern verwendete Befestigung für den Cam...

I've created a simple monopod specifically for the Logitech C270 webcam. This monopod was printed using my HatchBox PLA on the Hooklet 3D Odin One printer. The design of the parts allows them to join together without screws, but I did use a small...

This is a simple webcam holder I made to hole my logi webcam for octoprint time-lapse. ... It fits on the end of the Ender 3 pro Z-axis arm and holds the camera as a slight angle at nozzle height.

Simple Monopod for Logitech C270 Webcam. Specifically designed for the Logitech C270 model. Printed in high-quality HatchBox PLA on my reliable Odin One 3D printer from Hooklet 3D. The parts are cleverly designed to join together seamlessly without...

SummaryThis is a versatile mount for the Logitech c270 webcam that can be used on almost any surface.\nIt was designed specifically to attach to a 20x40mm extrusion rail on my 3D printer, and it securely fastens in place with a 3D printed bolt.\nThe...

How I Designed This: For this design, I merged the camera mount for the c270 webcam from http://www.thingiverse.com/thing:1159406 with the bolt clamp from http://www.thingiverse.com/thing:1159406. ...I made a minor adjustment to the clamp to make it...

This model has designed in order to hold in place the Logitech C270 webcam. We have been using this holder while we are making time-lapse videos and follow up the printing status via remote access by OctoPrint. There are some fasteners are needen...

Reinforced connection established between the web camera and the Logitech C270 device.

Individuals Mount C27 Webcam on 2020 Extrusion Bracket Easily.

A mounting clip for a Logitech C505 webcam. ...I have mounted my webcam to the ceiling of my 3D printing enclosure.

I adapted the remaining components from the Elnekr0 design, except for the webcam holder, and created an alternative solution.