logans run 3d models

 Happy printing! Printing Suggestions- I would print this in at least PETG- 4 perimeters, first layer height of 0.2mm and layer height of 0.15mm- 20% infill with the Gyroid fill pattern- I would use Organic supports (with "For support enforcers only"...

It can be thrown whole into a filament dehydrator to refresh the packets, without worry of warping. Assembly: Attach the bearings to the end of the rollers and snap them into the slots in the base (Optional, Glue them to the spindle so they won't...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 shape =...

 Replace the colored filament with clear PLA and finish the print.Material:  PLA (colored for the top layer, clear for the walls)Quality:  .12mmTemp:  200°CBed:   67°CPrint Speed:  50mm/s, first layer at...

When I went to a 6-Cell it cracked at the motor mount with PLA+ but has held up fine with PTEG and has over 30 runs on it. This is modeled after a P9 RC Rigger (Outrigger) Racing Boat. Turn fin is critical on this boat. Designed to take 7.8MM arrows...

Feed the wire through the channel that runs from the negative terminals all the way through the middle of the charger to the XT-60 connector.Apply CA glue to the back of all four terminals and stick them into their cavities. These terminals are...

Day 2: Unleashing Creativity Tap into your inner artist and let imagination run wild as you explore the realm of creative freedom. Push boundaries, experiment with innovative techniques, and witness the birth of something truly extraordinary. Day...

It’s important to restore this connection during the relocation process by running a simple and easy ground wire from the back of the PSU case to the raw metal end of the base frame extrusion. See required hardware list below (very inexpensive) and...

Two mountain beltways run along the east and west coasts. - There is a spherical chamber in the "very heart" of the moon. I made it displaced from the geometric center so that it can explain the displacement of the center of mass. - The chamber has...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

If you notice any warpage, you could modify your slicer settings to run the parts fans at 5% to keep them cool, I did not find this necessary. There are 5 sets of ducts, standard length, and ones that sit 1, 2, and 3mm lower, and 1 set that sits 1 mm...

9: Cut the remaining support off the axle and base flush until the cover runs clean. Marked red. Schneiden sie den restlichen Support von der Achse und dem Unterteil bündig ab, bis der Deckel sauber läuft. Rot gekennzeichnet. 10: Cut...

Have you ever worried about leaving your printer running for those long 20 hour prints? With a heated bed, hot extruder, and cheap power supply, there's a lot that could go wrong. I have worried about leaving my printer unattended and wanted an...

That way you can cut or slice it any way you would like.This model was also designed in a way to fit a small coin battery LED and switch to power a pico LED that runs to the mind stone piece (see below for further instructions). The coin battery LED...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes wall_thickness = 1.6 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

These should be printed lying down, with the inner flat faces up and down, so that they can be printed without supports and the layers will run lengthwise. Ideally the part should be installed so the inner flat faces are to the sides, which will put...

I've never even run into an issue like that yet.I designed this in TinkerCAD. Every part except for the backplate of the triple bearing design is custom. For said backplate I used one of @morganlowe's hotend designs and just cut off the top parts :)...

Also an X pattern runs throughout the major areas of the ship to reinforce the structural rigidity of the ship because of long duration periods of time and deployment. The ship is heavily armed as well should the ship and its network ever be...

This is a BIQU H2 mount for the base Ender 3/3 Pro and the Ender 3 V2. It comes in 2 variants, depending if you prefer to mount one or two 5015 fans.Key featuresdesigned for the Ender 3  and the Ender 3 V2 [new]modular, small, lightweight,...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes wall_thickness = 1.6 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

To get a light source inside the nacelles, I made a hollow chamber to run a positive and negative wire through the pylons to get into the nacelles. There is a small 4mm hole in the top and bottom of the AStarboard Forward Engineering section. This...