lock pick handle by bosnianbill by 3d models

To stop the box moving while driving I used one of the lashing eys in my trunk by adding a little hook to the box which could be hooked into the lashing eye. Another problem was that the cap of the canister was closed so I needed a solution to...

The polarity of the magnets must attract the wings on their insides.     I tried different approaches to perform the last step and you can try inserting the filament segments as shown in the picture but it is not the best...

By seating them in opposite sides of the wand, the system gets tensioned when the two halves are glued together.In the spirit of keeping it simple, I decided to just directly click a tactile switch to operate the light, rather than design and print a...

Also, I used these top slot supports, by super gluing them onto the PEI sheet as little grips to pull the sheets out. they look pretty neat like that.</p><figure class="image image_resized" style="width:68.07%;"><img...

Obviously I've made everything so that I'll get the best results with my setup. To put everything together you will also need two 50mm metal or plastic rods of a diameter of 3mm for the bed and two pieces of 60mm for the x-axis. How I Designed This...

I figured I was going to have to re-print this in ABS or ASA by now. I did make this with 10 perimeters and 50% infill. I was still learning 3DP at the time, and way overcompensated, but it seems to have worked. Original text: I recently purchased a...

Here's my attempt at replicating the Infinity Orb from the film Guardians of the Galaxy. In one of the pictures, you can see a side by side comparison of my orb and the orb from the film. I tried to replicate all the hole shapes to the best of my...

A comparison to the original version by Logitech/Ultimate Ears:OriginalThis Versioncharging indication LEDno LEDmicro USB jack (cable not included)USB-C jack*too big for the Boom 3 as this dock is designed to also charge the Megaboom 3perfect fit for...

My cutting surface was planed by the cnc with a surfacing bit so I thought pressure wouldn't help but it cuts so much more accurately and reliable with this small change. I have yet to test this design and currently loop a rubber band from the bottom...

On both models, I've found that if you rotate the model about the z axis by 15 degrees then the shell lines end up being perpendicular to the model, rather than at the standard 45 degrees. ...It makes for a nice finished look.</p><p>Category: Decor</p>

(Took me about 20 min for both). Now the upgrades: Front Z-belts tension tool While assembling the front belted Z pulley which also sever for tension the belts, I found it hard to adjust, so I did a tool which bolts on the frame and uses two of the...

By nature, LED light sources run significantly cooler than traditional lamps, reducing the chance of accidental burns and increased temperatures due to heat emissions. This solid state design of light emitting diodes provides a more reliable, stable,...

These are not intended to be precise step-by-step instructions. Proceed at your own risk. 1.) Remove filament from the machine using your normal method. Turn off, disconnect power, and wait for the hot end to cool. 2.) Remove the bowden tube...

Take care when pushing both parts closed as the link will easily break, a little sanding of the small chamfered part of the link can help it slip into place without breaking.The case should keep closed by itself, even if the link breaks, but you can...

As far as I know, the magnet's only purposes are to hold the data cable end in place when it's stowed, and perhaps also to serve as “screw storage” while working with the drive/case.&nbsp;Seagate HDD link to Amazon is an affiliate link.&nbsp;FAQ:Q:...

V2 -----> 210 x 200 x 105 mm GERMAN: Scube Mini: https://youtu.be/4cyErt50xus Software: https://youtu.be/jS2phfbw6GA Scube 7Inch: https://youtu.be/LRB2VFb4w6U ** inspired by the Openscan Mini Project ** --https://www.thingiverse.com/thing:4562060--...

I decided to do better. I designed the scepter in SketchUp by taking a side on picture of the Scepter from the movie previews and tracing it. I added what detail I could eck out of the relatively grainy footage. From there, I started until I had a...

by bending a bit on the hinges. Then you can put in a toothbrush and test the mechanism.&nbsp;</p><p>If it doesnt work:</p><ul><li>Check that the side connectors to the gripper arms are still straight to the front and rectangular to the thicker base...

While you still may giveaway your 36h printed helmet, or the articulated dragon, this model enables you to print a personal fidget spinning finger ring, printed on demand in minutes, with perfect fitting.&nbsp;“Rings are much more personal and a lot...

By distributing the powder evenly you reduce the chance of channelling and your espresso is always perfect (no guarantee!).Many WDT tools use acupuncture needles because they are very fine and work great. <strong>BUT I HATE NEEDLES!</strong></p><p>My...

If you can't find a topper that fits your needs, let me know and I can make it!Assembly-GearboxFirst, we'll start by assembling the most important part of the clock; the gearbox. The clock motor that I found was from Amazon, and you can find it...

So, have a look at the materials and tools lists in the PDF manual supplied with the files and decide for yourself if you want to take the extra effort.Speaking about the manual: I put some effort into documenting preparation, 3D printing, and...

It is a tight fit by design, so you may have to clean out the print a bit upfront to make it go in.Step 4: Slide the moving part on the rail. It should slide without too much force. If it does not, use a bit of sand paper to clean out your parts a...

The remote cooling is supplied by a standard 19mm CPAP hose. This was designed specifically for the Ender 5+ and Revo using the CR Touch, however I have included files that have been adjusted for the original H2 and Biqu’s hot end and CR/BL touch...

The model is saved in STL files, a format supported by most 3D printers. FDM version features: - Contain 16 parts.- Made with connectors.- The weapons are removable and inserted into the hands so that you can print them separately and combine at...

It was not planed but it worked perfectly.&nbsp;Start by inserting the Shaft inside the box.&nbsp;&nbsp;Use some glue in the knob and connect it with the shaft.&nbsp;&nbsp;&nbsp;Now the tricky part. I recommend you try your technique without any glue...

He is one of the Dragon Ball franchise's most popular characters.ABOUT THIS 3D MINIATUREThe model is saved in STL files, a format supported by most 3D printers. FDM version features:- Contain 6 parts;- Made with platform;- Made in running pose;- All...

Hunchback BattleMech 3D Printing Miniature is inspired by one of them. Of course, it is smaller than its prototype, but still fascinating. 50 tons of metal, starshield armor, a huge riffle on a shoulder - Hunchback looks really dangerous. And not...

To use an aio betaflight brushed flight controller like the BeeRotor TinyBeeF3 Controller by changing the pid values/betaflight settings to supress gyro/accell changes. Use other toy's boards that already have 2 integrated escs like small rc twin...

This is easily fixed by lubricating the screw (threads, inside, top and bottom) and the threads of the nut with silicone spray. <strong><em>Do not do this when assembled and let the silicone spray dry before assembling. Do not use any oil or grease...