loading filament ender 3 3d models

Guide for the filament in the Ender 3 and 3 Pro. The guide can be put in the top horizontal aluminum bar. ... This one will not use much material and will be finished in about 30 minutes

Filament Sensor for Ender 3 MAX. ...Limit Switch used is KW11-3Zhttps://robu.in/product/tact-switch-kw11-3z-5a-250v-micro-switch-round-handle-3-pin-n-o-n-c-for-3d-printers/

My direct drive ender 3's just allows the filament to glide back and forth on the top rail. ... Seeing the original remix work fine of my CR10's I did a quick remix to use the same setup on my enders without the filament sensors.

Ender-3 Pro Filament Sensor Mount Remixed from filament guide: https://www.thingiverse.com/thing:3052488 The filament I bought from Amazon (2 pack) $11 https://www.amazon.com/dp/B07N2GQHQT Print Settings Rafts: No Supports: No Resolution: 200 Infill:...

I made this bracket to hold my Sunlu filament dryer above my Ender 3 so that it is now the printer's spool holder so I never print with wet filament anymore. This let's you dry filament and print with it at the same time. ...Bracket will fit any 2020...

Improves filament guidance to the extruder while preventing filament contact with the Z-axis threaded rod.This is an accessory to the filament spool holder on the side of the printer:Ender 3 Filament Spool Holder UpgradePREPARATION FOR...

Ender 3 - Top filament guide Modified to perfectly line up with the Low Friction Filament Guide mount: https://www.thingiverse.com/thing:4134230 and Filament Guide (mount) thing: https://www.thingiverse.com/thing:2917932 or Z Leadscrew Support &...

... for More Awesome Projects! It's Fast and Easy to Assemble Create Your Own IKEA-Style Box for Your Ender 3 Just Place the Filament Inside and You're Done! Thanks for Watching! Bye for Now! ... ======================================================

This is a filament guide I designed for the Ender 3/ Pro in Solidworks 2020. ... Cura Settings found on All3DP that worked wonderfully: Printing Temperature: 200 °C Bed Temperature: 60 °C Speed: 50 mm/s Layer height: 0.12 mm Retraction: 6 mm @ 25 mm/s...

... in one! There are two parts, the body that is held by the rod screws, and the lid of the sponge container. It was designed for Ender 3, Ender 3 Pro, Ender 3 V2. Let me know in comments if it goes well with other printers. ... Enjoy it :)

Filament Holder Adapter Mounts Perfectly to Ender 3 Side. Absolutely no supports required, just pay close attention to part orientation in your slicer software (nut holes should face upwards). No extra mounting hardware is needed at all. Installed...

A custom-designed sleeve for the popular Ender 3 3D printer, engineered to prevent filament entanglement with the critical Z-axis screw, ensuring smooth and uninterrupted printing operations. ... (2/2/2019) An updated version of this innovative sleeve...

An Ender 3 and Ender 3 Pro filament guide and runout sensor. This setup utilizes standard mounting hardware, eliminating the need for new screws. To complete this assembly, you will require a small amount of Bowden tube. ...You'll also need one 14mm...

... but designed to slide into the rail of a 2020 frame member. ...It was designed specifically for the Ender 3 Pro, but should work on any Ender 3 series printer.It was designed in OpenSCAD.It is intended to be rugged. ...Printing in PETG is recommended.

Filament Guide for the Ender 3 Direct Drive Conversion Warning: Modifying your Ender 3 printer can significantly reduce its Z-axis travel distance, down to approximately 140mm. ...To prevent potential crashes, it's highly recommended that you update...

This is a wire guide for Ender 3 or Ender 3 pro 3D printer.

This is a remix of "V5 More Rigid Mount 2020 Ender 3 Filament Guide & Cleaner by FurioPrints" and "Ender 3 Filament Guide **UPDATED**" by robathome" I wanted better alignment of the filament at the entrance to the cleaner. The filament roller seemed...

I found the original design to be a bit tight in that area for my Ender 3 v2 model, leading to unwanted strain in the base.Redesigned the primary load path within the base and tried to get rid of as much excess material as possible, resulting in a...

A spacer used to centre your hatchbox (and possibly other) filament spool onto the Ender 3 holder. ...Greatly improves spool rotation since point of rotation is now at center.

This custom-designed piece allows easy installation of a filament sensor on your Ender 3 V3 SE. No additional screws needed! ...Attach the sensor securely to enhance your printing experience.

Revision of Holspeed "Ender 3 Filament Roller Guide" This is printed using the same settings as Holspeed. ... Utilizing Common 688 Bearing included with most dual Z or Z alignment kits

Ender 3 Filament guide, Star wars X wing I have had some comments saying the file is corrupt? ...I have redownloaded the file and printed it and it worked fine so not sure what this issue is..

This is a mount for the Biqu (Big Tree Tech) filament runout sensor for the Creality Ender 3. ... I have also included the Freecad file (0.18.4) so you can completely customize the mount as you wish.

This is yet another filament guide for the Ender 3 printer. ...The pegs that hold the guide into the 2020 extrusion are pretty tight, so they may need to be sanded ever so slightly for a better fit.

It's a little basket to store your filament runout sensor when you don’t use it. ...I designed it for my ender 3 but I guess it should be ok with other Creality printers which have the same bracket.

Yet another Ender 3 V3 Se filemnt guide, but this can cover 360° direction for filament feed.Additional components required: 2X zz809 bearing6.5.2024 upadate: Fixed bearing shaft so it can be printed sideways.

Here's how it works: Simply pull off the end cap, slide this filament guide into place right above the top support beam on your Creality Ender 3 and watch as your prints become much less likely to snap.

This is an essential upgrade for the Creality Ender 3 that streamlines the filament path, effortlessly guiding it into the printer and simplifying the extrusion process, resulting in a smoother overall printing experience.

i maid a base for the stock ender 3 spool holder so it's sepret from the printer it has no problen holding more then 1 kilo of filament to assemble you need two m3 screws

I have designed a part to attach the filament runout sensor to my Ender 3. The sensor holes are aligned straight with the stock extruder. ... Compatible with the widely available cheap sensor: https://www.aliexpress.com/item/1005001349519472.html