loading filament ender 3 v2 3d models

Another version of the same filament guide where the funnel is much closer to the extruder.

Ive created this minimalist filament guide to help support the filament coming in from my [Side / Rear Spool Mount](https://www.thingiverse.com/thing:5237821). It bobbles with the back and forward movement of the filament but still holds strong for...

I used a mini micro switch. ...The filament enters the extruder completely straight.

So I built an enclosure and had to detach the original filament holder from the 3D printer frame. ...This 3D print functions as a base for the original filament holder. Category: 3D Printer Parts

So I built an enclosure and had to detach the original filament holder from the 3D printer frame. ...This 3D print functions as a base for the original filament holder.

No screws, no supports, 608 ball bearing filament guide designed to fit in the Filboyt filament guide mount. Combine with thing:4683505 (lower) for a complete the set of no screws, no supports, upper & lower filament guides. ... In the pictures the...

This is my filament guide to avoid tension on extruder entrance. Press only install, no screw required. ...

Modified filament guide clip for use with M5 flat head screw. ...Requires to cut M5 threads in the extrusion piece.

Top filament guide frame with different attaching system to printer frame. ... Other parts are used from original design.

https://www.thingiverse.com/thing:4735175 Did not fit on my Ender 3v2 machine because there was a metal plate on the "bottom" of the X stepper preventing a decent mount. I made the sleeves that grab the axis longer to make it fit. ... The pulley...

Printed in PLA , 0.8mm top, bottom and walls, with 10% Gyroid infill Remixed with Ender tool holder slide-in-rail clip , flipped over to print flat and resized to 110mm away from gantry. NB works well, but slide in clip could do with some resizing...

Just a little roll for to put between the original holder and the filament spool, so it doesnt wiggle arround that much while printing.

Just another filament guide. slip on, so no need for any tools or bearings. ...print without support, and put in place

3cm longer version of the filament feeder to better fit with the https://www.thingiverse.com/thing:4683505 In the original version, the filament goes at a very sharp angle in two places and doesn't come back on the spool for me.

I wanted a simple guide to keep the filament running into the extruder at a better angle and the ones I had seen were a bit too much work for what I wanted (I personally prefer fewer moving parts), so I designed this. ... Just over an hour to print and...

I wanted a simple guide to keep the filament running into the extruder at a better angle and the ones I had seen were a bit too much work for what I wanted (I personally prefer fewer moving parts), so I designed this. Just over an hour to print and...

I printed below(2917932), but the base is not so solid and weak(too short), so I remix it with other designs (4570426 & 4823360) Filament Guide_Guide_Open and Filament Guide_Guide_Flat are from 2917932. ... https://www.thingiverse.com/thing:2917932 ...

... au centre et ne touche pas le bord du levier. J'ai aussi intégré un support de câbles. With this filament guide you will be able to print these great objects: https://www.thingiverse.com/thing:4853538 or https://www.thingiverse.com/thing:5004757

... au centre et ne touche pas le bord du levier. J'ai aussi intégré un support de câbles. With this filament guide you will be able to print these great objects: https://www.thingiverse.com/thing:4853538 or https://www.thingiverse.com/thing:5004757

No screws, no supports, 608 ball bearing filament guide designed to fit in the Filboyt filament guide mount. Combine with thing:4683505 (lower) for a complete the set of no screws, no supports, upper & lower filament guides. ... In the pictures the...

This will stop your filament touching the greasy Z Screw Rod, and also if you run it like I do from my Sunlu filament holder it reduces air and moisture getting to the filament Print to your usual settings for any small print, any material will...

This is a spacer that prevents the filament from touching the greasy z-axis screw. ... It requires a minimal amount of plastic and can be fitted without any additional screws.

Discovered that having the filament feeding from the side was better. Tried various downloads but decided to design my own. The aims were to have adaptability to various roll widths. Use skateboard bearings to reduce drag and friction. Easily fitted...

Discovered that having the filament feeding from the side was better. Tried various downloads but decided to design my own. The aims were to have adaptability to various roll widths. Use skateboard bearings to reduce drag and friction. Easily fitted...

Print with supports touching build plate0.2 layer height3 walls

Update: This design is superceded by my single-roller design over here: https://www.thingiverse.com/thing:5330621 This is an alternate top filament guide for this thingy: https://www.thingiverse.com/thing:3428924/files . You will need two spacers and...

This is a simple filament guide I made because I did not like that the filament would rub against the Z-Axis Guide Rod when printing. To mount, all you do is remove the 2 screws beside the guide rod and slide the piece over. Once done, reinstall...

I wanted a simple guide to keep the filament running into the extruder at a better angle and the ones I had seen were a bit too much work for what I wanted (I personally prefer fewer moving parts), so I designed this.Just over an hour to print and...

A piece is added to be able to use the tool more comfortably.It allows us to hold the extruder so that we can change the filament more easily and with more care.Two pieces are printed at a time and then glued together.

Double roller filament guide which works well with seperate desktop spool holders (or other seperate spool holders).You`ll need:1x bracket2x wheels4x spacers, Additionally:2x 608 roller bearings2x 16mm (minimum) M3 bolts with hex nuts.NOTE: Bracket...