livescope transducer protector 3d models
14024 3d models found related to livescope transducer protector.
thingiverse
I adjusted the Livescope_Mount_v4.stl to include a cap (Livescope_Mount_Cap_v1.stl). I had an issue with the bolt that mounts the actual transducer on would loosen over time. I was worried it would be at the bottom of the lake eventually so...
thingiverse
Mount for the new Garmin livescope transducer for use with perspective mode. Best when printed with PETG or ABS. Nylon is nice but just a bit too flexible for my tastes. ... Enjoy.....
thingiverse
This part is for the Garmin Livescope transducer. This part should help prevent the transducer cable from cracking/breaking when it meets the transducer. ... Additional Items needed to attach part to transducer: -4 Stainless M4-.70x12 screws
cults3d
This is a protector for the Garmin Panoptix LVS32 transducer cable output, as it is a weak point that has and so we will avoid that it breaks there and then have no fix. Easy to place and that with two M4 screws will be subject, quite resistant with...
thingiverse
I created this so I could use my Livescope System Ice Fishing without having to spend $150 on one from a store. The pole is one half of a kayak paddle. The paddle is 30mm in diameter. The adapter was designed to slide over the smaller end of the...
thingiverse
Protective cover for expensive Livescope transducer. ...
thingiverse
This is a tripod design for a extendable paint pole, to use for Garmin Livescope transducer ice fishing. Should fit any pole with a 1.25" OD. Connected with 1/4-20 1.25" round head screw & nylon locking nut. ... Pole I used: ...
thingiverse
I will probably update it to screw on to the top holes of the transducer eventually. I uploaded an updated version of the tripod mount. The original was a little thin where the bolt goes through and was prone to cracking/breaking. I used 4...
thingiverse
This is an arrow used on my homemade transducer pole for the Garmin livescope. It fits standard 3/4 PVC fittings. It is shown glued to a 3/4 PVC tee. Nothing fancy. ...Just makes life easier.
thingiverse
This is a clip used to secure the Garmin Livescope transducer cable to attach to my homemade mount. Was using electrical tape but did not like it when I spun the transducer head around too far. Was concerned about binding the cable too much. Made...
thingiverse
transducer bracket great transducer bracket works great 100 fill thats what i did strong
grabcad
Pressure Transducer with connector.this type of transducers can be used on various machines.
thingiverse
transducer mount for 10mm rod to slip down the same hole your fishing in without taking any space , fits smallo transducer like the gt20 and so on
grabcad
A pressure transducer measures air or liquid pressure and converts it into an electrical signal.
grabcad
Designed as a fix for a damaged headphone's transducer, this print provides necessary support to ensure its continued functionality.
thingiverse
Simple small transducer mount for 10 mm pole to put in the drilled hole when icefishing , the opening of the gap is 15mm and fits all small transducers like gt20 style . ...the stl file includes 2 small washers with thickness 0.5mm so the transduser...
thingiverse
The original had internal voids where the transducer screwed into it. I fixed those. I printed with PETG at 100% infill on Simplify3D by setting the bottom layers to more than the total layers. ... Printed very strong that way.
thingiverse
Mount a transducer arm and its companion bracket to the Vexilar ultra base securely. The base-mounted bracket spans the factory's 1/4-20 bolt hole located at the front of the ultra base. ...Three 1/4-20 x 1" bolts coupled with one nylon lock nut...
thingiverse
The two attached files DO NOT have this writing on them.) These two pieces join together (Via one 1/16 bolt) to create a transducer arm for your ice fishing sonar. It has about an 8-inch reach and is pretty strong. ...It has two counter-sink holes for a...
thingiverse
This hold the transducer over the hole for a humminbird ice 55, 45, 35. It might work with the other ones. It mounts to an existing post using the existing hardware were the cable is wrapped up. It's a working progress. I just have to adjust some...
cults3d
... probe. ... 3 versions of the bracket that fits on a 20mm diameter, 25mm or 30mm tube. I can offer other version for other diameter tube on request. For the assembly you will need: 4 M6 nuts 1 M8 nut 4 screws M6x25 (supplied with the Livescope)
thingiverse
These cable clips are sized accordingly to fit the pole that I use for my Livescope Ice Fishing Bundle (Summit Fishing Equipment). Small, medium, and large clips to fit each section of the pole. The clips also feature a tab that locks the clip into...