little elephant architecture 3d models

I wanted something fun to print with this stuff. The lamp hides a wifi led controller in the base, and the base is then supplied with a little added weight by stuffing it full of spare washers and then hot glue to keep them still! The rings are...

I think mine were roughly 9 inches/22 cm; longer is easier to work withCut a small length of aluminum wire and wrap around the center (this is just to hold everything together temporarilyCut another length of the black nylon thread, exact length...

Generally, there is little room to spare. 4. Add some strong glue to the bottom of the rails and attach the rails on the tape. If you have printed an extension, you’ll need to place the larger rails 50mm more back than you would have otherwise. ...

100% infill is best I found. Easy to wash. Minwoo Choi's design on PrusaPrinter was a validating design and has some evidence of adoption (very nice!), but after comparing this design, the edges needed beveling, the sizes were too small, and the...

A little re-cap here. The fork and it’s bottom sealed bearing remove as one piece. The bottom headset cup is a snug fit for the outer ring of the bearing and this cup stays with the frame. The top and bottom sealed bearings are a snug fit in the...

I prefer the EiBotBoard driver because the Inkscape driver plugin that Evil Mad Scientist created for their AxiDraw will work with it with a little re-configuration and I find this to be very intuitive and flexible. I've added the OpenScad file now...

It may take time working backwards on an issue as this with a little bit extra background from other things he has experienced during whole period (so many variables that come to picture, but this one's case does look too abstract so could only share...

* 2022-09-26 iteration V11: updated floor / coupling * 2022-09-26 iteration V10: making planks a little smaller so have a cleaner gap, when printing, changed the brakes, as mentioned only between the wheel-sets. * 2022-09-26 iteration V09: minor...

You have two options here: Use the controller in the direction it was intended, but you will have to remove the two little holes. Otherwise, it won't fit into the shell.</li> <li>Remove the transparent part at the bottom, remove the circuit with the...

Hint: give a little extra push, just about 2-3 mm. Finally, tighten the screw.</p> <p>OK, if all mechanics are working as expected, your useless machine should work as expected. You can now close the housing, using the last 5 M3*10 screws.</p>...

, then tighten everything immediately but a little at a time and on several points. Let's say that it is not a chore for those who have a printer for a short time. The big work is at the beginning, that is, disassembling the original trolleys and...

Connecting the ducts to the manifolds on the thrust chamber can be a little challenging, so multiple sets of hands can definitely help 31. For the tension rods on the high pressure ducts, I used 3/32” aluminum tubing from Hobby Lobby. 32. For the...

Once those 3 pieces are glued up and dry move on to the left side pieces.If you're using the honeycomb pieces, they can be a little tricky, just make sure you get every touching-surface glued and aligned solidly. Once all those sections are dried,...

Screw the lamp holder container onto the lamp holder, the lamp shade holder onte to tlamp holder, and the little lamp holder top cover. ...Be aware, that when finally screwing the lamp foot together, simultaneously counteract the twisting of the...

2 12" long 5/16" threaded rods (or ~300mm long 8mm threaded rods) 28 5/16" nuts (or 8 mm nuts) 12 608 bearings Tub - I used a 21-quart Sterilite non-sealed tub, but anything of similar size will work nicely 24V power supply - I used...

It sticks out a little bit but the case is still able to sit flat on the table. The fan is placed so that it evacuates the case just like in the original design.</p><p>There is also a small spacer for the fan because I only had M4x30 screws and they...

... AVAILABLE:&nbsp;</strong></i></p><p><strong>R.E.P RATCHET XL!!! it is 200% bigger, and a little bit better.Print Download Page:https://www.prusaprinters.org/prints/89537-extra-large-rep-ratchet&nbsp;Enjoy.

In case you lose track of how many printers you have or just want to dress them up a little bit.Supports are painted on the inside and easily removed.Quick and easy printDesigned on...

Because the printer, as a normal part of the Auto Home process, may try to raise the Z axis a little bit more (ie 10mm) which was already at max level and touching the micro switch. This may harm the mechanical parts of your printer or the micro...

Ever since i saw it on google i wanted to make it myself but after checking the instructables page i changed my mind since it was a little bit outdated in terms of components and convenience. The main downside of that design was the use of mains...

It's easy to break or crack the little fingers. Slide the right wheel and axle through the right_bevel_gear assembly. The bevel gear should spin freely on the axle without a lot of wobble. Then slide the right ratchet onto the axle. Next is the left...

Now insert the tuning slide and wait until the glued is dried a little. Now practice putting the next two parts together on the trombone without glue. Then apply glue on the inside of the bottom brace, and the top joints of both the neckpipe bottom...

You may still have to push the magnet a little further down with a plastic or wooden tool. Keep one at hand since CA glue is fast. That method solves the two challenges I mentioned before.</p> <h3>How I Designed This</h3> <p>This is the third version...

Ideally you should have a little squeeze-out, which you can easily scrape off with the lollipop stick or wipe off with paper towel.Clamp the mould together - I use 3 two-inch spring clamps for each mould. Other clamps, or even elastic bands, would...

With a little effort, you will succeed.Cover_for_Ring_Transparent must be transparent!&nbsp;Step9:Place assembled Ring and Phone_Stand (optional) on Adapter_Mount and fasten them with the...

Too much petroleum jelly, and they won't catch a spark, too little, and they either can get wet, or they burn too quick. The right ratio should yield a water resistant tinder, with a good 1-2 minute burn time, and since they are super cheap to make...

The wizard noticed the little boy looking at him with big eyes, and showed him some magic tricks. Feris was in absolute awe over this visit, and after that day slowly turned away from his father's shop to pursue the arcane. Feris was obsessed with...

I've spent a long time making, testing, and documenting this and my only reward is that little stupid 'like' counter, download counter, and photos/stories from users. DON'T DEPRIVE ME OF MY ONE SENSE OF SELF WORTHThe actual license is Creative...

The EPL-LP-12-LED is an ideal for applications with little space where low profile fixtures are required.LED Benefits: Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation...

Do the same for the other end of the string such that the length of string is a little bit longer than the height of the barrel. The BandToStringLoops should be nearly touching the top and bottom of the barrel. Now use your two large rubber bands...