linnmon desktop 3d models
17801 3d models found related to linnmon desktop.thingiverse
Desk top power bar mount for the IKEA LINNMON desktops. ... I put 3 screw holes on the bottom of each mount but it only requires 1 to hold it in place.
thingiverse
Designed to neaten cable routing through the Ikea Linnmon desktop. Drill a 22mm hole, gently tap the cable channel into place, run cables through the channel and then insert the cap. ... 37mm deep.
prusaprinters
So, I designed an extremely sturdy (translation: over-engineered) anchor to do just that.The anchor attaches to the solid edge of the LINNMON/LAGKAPTEN desktop, with one screw in the side and two through the bottom. The desk can then be attached to...
thingiverse
... ones I found on Thingiverse were for small charger cables and were a little too delicate for my needs as I wanted to hold HDMI, ethernet, power cables, etc. ...so I designed this on TinkerCAD. It fits Ikea LINNMON and/or any other 34mm desktop/shelf
thingiverse
Remix of 8BitDo Sn30 Pro+ Stand & Linnmon Table Headphone Hanger
thingiverse
Simple cable holder for IKEA Linnmon tables. ... Sits very tight and doesn't move around.
thingiverse
This headphones holder can be used on LINNMON table from IKEA.
thingiverse
Ein Kabelhalter für den IKEA Linnmon Schreibtisch, zugleich auch ein Abstandhalter zur Wand.
thingiverse
Cord holder for IKEA Linnmon tables. ... Tabletop height: 34 mm, cord gate: 3 mm, holder width: 20 mm.
thingiverse
IKEA LINNMON PHONE CHARGE CABLE HOLDER You may need support. Locking mechanism is quite tight. ...Works well.
thingiverse
I remixed the existing design of this Headphone Stand to fit a Linnmon IKEA table (3.5cm instead of 5cm). ... Credit goes to the original design.
thingiverse
A mount to hold my Cisco Router under the IKEA LINNMON Table. ...It is not beautiful but under the table the design is not important for me.
thingiverse
Headphones holder for IKEA Linnmon table. ... I slightly changed the angle of the bottom surface so that the holder fits better on the table.
thingiverse
The actuall parts here in thingverse are not fits to my Kallax System so I design a new one, that is suitable to my Linnmon and Kallax. The first version was good, but not so stable that think first (my dauthger move the Linnmon and fall down). So,...
prusaprinters
Monitor stand legs fitting for an IKEA Linnmon table so you can put a monitor stand onto it. ...For those that like things in ultrawide.</p><p> Requires an 18mm thick wooden board that is as wide as the table and some M4 Spax screws.</p>
thingiverse
A simple wall spacer to put between an IKEA Linnmon (or similar 34 mm thick desk/table) and the wall to get some room for cables. ... Also includes a slot underneath for a 3.6 mm zip tie to hold cables.
thingiverse
Connector for linnmon table --------------------------------------------------------------------------------------- Print it vertically with maximum number of walls for more strength. ...
thingiverse
It's designed for Ikea Linnmon tables, but with the screw it can work with other tables down to 3cm thickness. If you have any problem or you have any advice how could i improve the model let me know in the comments. Feel free to post your makes....
thingiverse
This model is for connecting a Linnmon table top (100x60) to a 2x4 Kallax shelf. It's incredibly sturdy, despite the discreet design. I can lean on the table with my entire body weight without any problems. What you need, of course, is: Linnmon...
thingiverse
It is specifically designed for ikea linnmon, but it is suitable for 34mm thickness. This design is intended to keep the headphones inside the desk, and support headset up to 35/38mm of thickness (tested with Logitech G533). I'm using a...
thingiverse
Have an Ikea Linnmon table? Have a pair of large headphones? Now you can hang your headphones from your table. Expected table thickness is between 32 to 34 mm, so it should clamp down securely without damaging the table surface. MK 2 Version Adds a...
3docean
... a real scale in accordance with the original. Length: 120 cm Width: 60 cm Height: 74 cm LINNMON / ALEX table, white white stained oak effect, white, 120×60 cm – 992.143.04 Rendering: V-Ray 3.40.01 and Corona Render 3 Polygons – 562 Vertices – 844.
thingiverse
We attached the [IKEA LINNMON Tabletop](https://www.ikea.com/us/en/p/linnmon-tabletop-black-brown-80251358/) to a standing desk mount to put all our computers for remote working. Problem is, we would sometimes push the table too far into the wall,...
prusaprinters
Have an Ikea Linnmon table? Have a pair of large headphones? Now you can hang your headphones from your table. ...Expected table thickness is between 32 to 34 mm, so it should clamp down securely without damaging the table surface.</p> <p>MK 2...