lineloc 3 cord tensioner 3d models

This device features an elastic cord, which is threaded through a hole and tightened by rotating it 90 degrees. As I await my ToM's arrival, I am uncertain about its print quality or clearance efficiency; however, enlarging the bolt holes should be...

My previous Cord Tensioner, 875245, let go of the cord whenever it was pulled at an angle. But now, I needed one that wouldn't release the cord regardless of the angle at which it departed the tensioner. This new design is intended to install under...

Simple and easy to print tensioner. ... cord tensioner.1 = grey one cord tensioner.2 = orange one

Simple and easy to print tensioner. ... cord tensioner.1 = grey one cord tensioner.2 = orange one Layer height: 0.2mm Wall thickness: 1mm Wall line count: 2 Infill: 100% Skirt/brim/raft: No Support: No

Simple and easy to print tensioner. ... cord tensioner.1 = grey one cord tensioner.2 = orange one Layer height: 0.2mmWall thickness: 1mmWall line count: 2Infill: 100%Skirt/brim/raft: NoSupport: No  

A simple cord tensioner hook to be used for guylines, ridgelines or lines of any sort when camping or during other cordage-intensive activities. I use (and recommend) it in combination with my BEEFY TRI-LOBE TENT STAKE CAP for a killer tarp-staking...

A simple cord tensioner hook to be used for guylines, ridgelines or lines of any sort when camping or during other cordage-intensive activities. I use (and recommend) it in combination with my BEEFY TRI-LOBE TENT STAKE CAP for a killer tarp-staking...

At its core, the primary purpose of this cam-based anchor is to maintain tension in a ratchet wedge, facilitating engagement with the cord. Printing pre-tensioned springs is impossible, so the anchor alone cannot grasp or retain the cord. To...

A custom repair job was undertaken to replace a faulty blind cord tensioner with a makeshift solution using a spare human part.\nThe design for this adaptation was crafted from scratch within the CAD software Freecad, drawing inspiration from the...

...If just scale the STL if you want to use different cord diameter.I use them to replace the big & heavy ones my backpack came with to get it closer to “ultralight” gear.The 2mm version (printed in red) is made to be hooked into another 2mm cord loop.

 The rubber-band tended to break anyways.Added grooves on the tensioner body and cam to provide better “bite” into the cord.  It works really well now.Added handle feature to the cam so you can release the tension  as needed.Other...

This is a cord tensioner for 4mm paracord.It is a remix of a thing I found on Thingiverse by @cadfinger.https://www.thingiverse.com/thing:1486048Things I've changed:Removed rubber-band features because it was too small to be useful.  The...

... If using a 0.6mm nozzle, use at least 3. 3) Whatever material you use, print on the hotter side of what is allowed. More heat = better bond = more strength. ...I printed mine in PLA at 220C.<br/> 4) Used rectilinear infill pattern at 20% infill.</p>

Print instructionsThe four main factors for printing parts for strength, in order from "most important" to "least important" are: 1) Print Orientation 2) Number of Perimeters 3) Printing Temperature 4) Infill Percentage Therefore, to maximize...

We tightened the cord on our shades, but the tensioner itself lacked a retaining clip. It kept twisting loosely as we fiddled with the cord's slack. To secure it firmly, I screwed a wall anchor into the drywall and then drove in a tapered head wood...

Please note that you should only attach lightweight stones and use a sturdy cord to prevent any damage to the aquarium. This device pairs well with glass no thicker than 5 mm. Printing Details: The material used for this device is PLA. Each layer is...

Hunter Douglas Cord Loop Tensioner Mounting Bracket with approximately the same dimensions as the original. ...Hole sizes and countersink are the same.

The cord tensioner is a friction fit for a 12.5 mm ID I replaced the cord with a 1.18 mm paracord, which required it to be checked for tension against the other working pole. The part can be glued into the top of the pole section if required. ... ...

This is a tested precise replica for a set of specific clip-on cord tensioner and a matching window frame mounted bracket for cellular shades (AKA pleated shades, pleated blinds, etc). I had to design these replicas because some of mine has broken...

• Webbing slot: This version replaces the round hole with a slot matching the Lineloc 3 cord tensioner's width. When paired with a Lineloc 3 tensioner attached by webbing to the stake, this setup can be used with any tent. ... This new design is still...

Cord Winder 3 versions 3 versions to print on 220 mm 0r 300 mm bed

I chose to print this design with White Soft PLA, which boasts exceptional flexibility, making it simple to squeeze the cord into place and allow some degree of bend throughout the entire assembly. Not exactly your cup of tea? ...Be sure to check out...

A simple solution to containing cords on Ender3. Uses 2x M3x8 bolt for mounting (shorter ones will do too). ... Inspired by awesome r/Ender3 Reddit Community

This thing was created with Tinkercad. Edit it online at https://www.tinkercad.com/things/e29usH4ZW5v Printing specifications include a printer of e3D BigBox, with rafts set to No and supports also set to No, resolution is .25mm, infill is 50%.

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/e29usH4ZW5v Print Settings Printer: e3D BigBox No Rafts No Supports .25mm...

This is a custom extruder tensioner designed specifically for the Creality Ender 3. To assemble it successfully, you'll need to apply superglue to a thin M4 nut and attach it to the bearing screw. For optimal results, print this part at 100% infill...

If you are interested in camping you have probably come across 3 hole tensioners. They generally come with tents, hammocks, and other gear that require guy-lines. They are very simple to use and allow you to increase or decrease tension of guy-lines...

Ender 3 Y tensioner, based on the design from . Enhanced thread dimensions to reinforce nut and shaft threads' reliability. ... Streamlined shaft for printing directly along it, reducing the risk of part breakage.

Belt tensioners for X and Y axis

Update: I recommend using my newer design which allows the use of a spring, helping the tensioner to work better: https://www.thingiverse.com/thing:3529205 This is an threaded extruder tensioner designed to help with more consistent extrusion on your...