linear rail kit ender 3 3d models

Ender 5 Plus X axis Linear rail with a BMG direct drive. Made using Ender 5 plus linear rail modification from: https://www.thingiverse.com/thing:3960105 and added a BMG direct drive and a cable management on the side. Print instructionsCategory: 3D...

Ender 6 X&Y MGN9 Linear Rail mod.Fully compatible with Creality top covermovable Y endstop mount (you can set from 250 mm to 275 mm. If you cut Z screw by 2-3 cm and have PEI you can set Y enstop even to 290 mm)Use many stock screwsI edited few...

I created a custom belt holder for my Ender 2 Y axis MGN12 linear rail mod, which I sourced from Pumpal's design on Thingiverse. To replicate this mod, you'll need to download the original files and use the same screws that Pumpal specified. ...My belt...

An upgrade to fix the not linear Y Axis extruded bar

... mashup of two excellent files. ...Thanks to the creators! Untested as of now. I will make updates if needed although I doubt there will be any issues. Additional parts are needed so see the Belt Driven Ender 3/Pro/V2 and CR10 page for those files.

3.3.1 (If you choose a 500mm linear rail, cut it to size so its flush on both sides) 3.4 Take your linear rail, with your block and choose 4 holes on one rail and evenly spread out 4x M3 Screws. do it on frames for each side. 3.5 Attach 4 T nuts on...

Linear rails AND a lightweight direct drive extruder via the Biqu H2 are a great upgrade for your Ender 6. I designed this solution as I wanted to convert to linear rails as well as direct drive with the minimal number of adapters (this is a 1 piece...

Linear rails AND a lightweight direct drive extruder via the Biqu H2 are a great upgrade for your Ender 6. I designed this solution as I wanted to convert to linear rails as well as direct drive with the minimal number of adapters (this is a 1 piece...

My very first published remix. I moved the pully cable holders so the pulley cable fits. I found it impossible to fit the existing cable to the original design by badadz so I went about remixing it. I also added a horizontal cable holder on the...

Print at 100% infill. You will want to install the stock bed carriage without the wheels on to these blocks. ...Keep all the bolts loose and then tighten them incrementally while sliding the bed fore and aft to ensure proper alignment and free motion.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/c273Eg0x76w

This a remixed limit switch holder since the original limit switch adapter didn't fit at all. There was just no space for it. It bolts onto the extrusion with the motor mount and screws. ...No additional hardware is needed.

My very first published remix. I moved the pully cable holders so the pulley cable fits. I found it impossible to fit the existing cable to the original design by badadz so I went about remixing it. I also added a horizontal cable holder on the side...

This is a remix where the bottom holes are spaced to match the bed, the Standard Ender3 has a 2020 extrusion, and the original part was made for the 2040. ... I use the pre-cut holes in the bed (newer version, the "square-aligned wheels" one)

I changed the belt mount slightly to give a little more clearance for the belt. I have new belts which are crimped with zip ties and I found that it rubbed slightly for whatever reason as it left the belt mount. ... This replaces the...

This is a remix where the bottom holes are spaced to match the bed, the Standard Ender3 has a 2020 extrusion, and the original part was made for the 2040. ... I use the pre-cut holes in the bed (newer version, the "square-aligned wheels" one)

Even after putting the offset bracket all the way back and removing the lever from the switch my bed was still 4-5 mm short, so I've extended the bracket another 6mm (will reach the corner of the stepper motor)

Remixed Into Thicker Belt Clamps.

Made the webcam arm a bit stiffer as it was wobbling quite a bit at higher speeds and adapted the endstop mount to accept the arm. ...

needed a custom extruder motor mount since the one I had would no longer work with new set up. ... This uses 2- M3x6x5 brass inserts and tree supports printed in PETG.

I made a belt holder for "Ender 2 Y axis MGN12 linear rail mod" from Pumpal. https://www.thingiverse.com/thing:3478163 You need to download his files, too. You need the same screws he used for this mod. I just made the belt loop is going parallel...

So here it is, an Ender 6 linear rail mod for the Y axis that mounts on the inside of the frame. The mounts allow you to use the original factory cover from creality. I had to sand a little and clean up the holes with a drill but not much to do...

My take on a switching hotend design. I designed this to take two standart creality hotends, a servo (I used:...

Here is my own construction for a Phaetus Rapido HF, LDO Orbiter V2.0 on an Ender 5 Plus with linear rail. 2 x 5015 component fan, 4010 or 4020 hotend fan, BL Touch bracket and top cable routing. Put the fusion file in here, if you want to...

I designed this to take two standart creality hotends, a servo (I used:...

This is a Cable Holder for the Ender 5 Plus with linear rails and the Micro Swiss Direct Drive I use this cable chains 20x10mm: https://www.aliexpress.com/item/32999589537.html?spm=a2g0s.9042311.0.0.27424c4dZDh4ri I use the cable chain trays from...