linear rail ender 3 3d models

This is a remix of three parts to fit the EVA2 carriage (for different extruders and hotends) to an Ender 3, Ender 3V2 or Ender clone with x-axis linear rail installed in front of the 20x20 extrusion profile. Standard EVA2.3.0 only works with...

While installing a set of tech drawers (https://www.thingiverse.com/thing:3831119) into my Ender 3's front sections, I found that the linear rails on the Y-axis were just a few millimeters too low to clear the top of the drawer casing. After printing...

I ended up putting an ender 3 v2 hotend on my ender 3, with a Sprite SE extruder (and linear rail)After a few attempts this is what I've been using - cable chain support is remixed from mwnickerson CHPower Direct Drive Drag Chain as the...

While attempting to install a set of tech drawers (https://www.thingiverse.com/thing:3831119) into the front sections of my Ender 3, I discovered that the linear rails on the Y-axis were just a few millimeters too low to clear the top of the drawer...

Pre-lube everything if you want to do it now or save the mess & wait until its mounted.BOM1 x Ender-31 x 300mm MGN12H linear rail2 x M4x20mm screws2 x M4 t-nuts2 x M4 washers4 x M3x25mm screws16 x M3x8mm screws12 x M3 t-nuts4 x M3 locknuts12 x M3...

# BOM * 1 x Ender-3 * 1 x 300mm MGN12H linear rail * 2 x M4x20mm screws * 2 x [M4 t-nuts](https://www.amazon.com/s/ref=nb_sb_noss_2?url=search-alias%3Daps&field-keywords=m4+tnut) * 2 x M4 washers * 12 x M3x8mm screws * 12 x M3 t-nuts * 4 x M3x25mm...

Here's a brief summary and analysis of the content: **Summary:** The document provides step-by-step instructions on how to modify an 8-bit Delta printer to use MGN12H linear rails. The modifications include drilling new holes in the Y plate, mounting...

Pre-lube everything if you want to do it now or save the mess & wait until its mounted.BOM1 x Ender-31 x 300mm MGN12H linear rail1 x M8x60mm or 1 x 5/16x2-1/4" bolt1 x M8 washer or 5/16" washer1 x M8 locknut or 5/16" locknut2 x M4x20mm screws2 x...

Rear mounted case for a SKR 1.4 (Turbo) mainboard, a 40x40 fan and a Raspberry Pi in combination with the 3DFused Y-axis linear rail kit. The case consists of 4 parts to be easily printed on almost any 3D printer. ... For the connection between the...

My very first published remix. I moved the pully cable holders so the pulley cable fits. I found it impossible to fit the existing cable to the original design by badadz so I went about remixing it. I also added a horizontal cable holder on the...

This is a remix where the bottom holes are spaced to match the bed, the Standard Ender3 has a 2020 extrusion, and the original part was made for the 2040. ... I use the pre-cut holes in the bed (newer version, the "square-aligned wheels" one)

This is a remix where the bottom holes are spaced to match the bed, the Standard Ender3 has a 2020 extrusion, and the original part was made for the 2040. ... I use the pre-cut holes in the bed (newer version, the "square-aligned wheels" one)

My very first published remix. I moved the pully cable holders so the pulley cable fits. I found it impossible to fit the existing cable to the original design by badadz so I went about remixing it. I also added a horizontal cable holder on the side...

These blocks will stop the x axis gantry at a precise height to make the Marlin "Mechanical G34" work with linear railsYou will need to activate Mechanical Gantry Calibration in Marlin, by uncommenting...

I have the following Rail kit from Creality, but it looks like they changed the rails: https://www.banggood.com/Creality-3D-Linear-Rails-All-Kit-for-Ender-3S-or-Ender-3-Pro-3D-Printer-Part-with-Leveling-Sensor-p-1728277.html?cur_warehouse=CN I was...

Just a little remix to use the X Axis Belt Tensioner with an Ender 3 v2 with BLV Linear Rails upgrade. The 2020 Extrusion in the picture was shorted by 8mm. It will fit nicely for the stock length. There is a center piece for 5mm and 4mm Idler...

Just a little remix to use the X Axis Belt Tensioner with an Ender 3 v2 with BLV Linear Rails upgrade. The 2020 Extrusion in the picture was shorted by 8mm. It will fit nicely for the stock length. There is a center piece for 5mm and 4mm Idler...

3d printable parts to upgrade ender 3 x axis with 250mm ball bearing linear rail and improved duct. Compact design with cable management groove, 40mm fans housing and bl-touch bracket. Perfect to have a clean setup with an accurate and sturdy x...

https://www.thingiverse.com/thing:4976865 This remix will allow seamless integration with the following upgrades to you Ender 3 (V1, V2 & Pro) as well as Voxelab Aquila. 1. Linear Rail X-Axis (300mm in length MGN12-H Linear Rail) 2. Bltouch 3. ...

The mount on my Ender 5 w/ a Mosquito Magnum, MDD 1.3, and linear rails was not stable enough. I was getting some bouncing. I could not use a gantry clip because the rails were in the way. I added one more mount point that uses the screw that...

https://www.youtube.com/watch?v=JfpxVBl5oqM Z Axis Linear Rail Lift Mod using the Outside V-Slots for Ender 3 and Aquila ------------------------------------------------------------------------------------------------------- I saw a mod that used...

... 5 3 x 20mm bolts and self locking nuts, 2 4 x 25 mm bolts and nuts, and a 5 mm nut. ... I printed in eSun PLA+ 0.6 nozzle 100% infill the two linear rail supports, Spectrum petg the hot end adapter. I've added a little support to hold the wiring. ...

... use a very tight/high quality rail for Y. This allows the use of the blue annodized carriage direct onto 2x 300mm 12H linear rails. Edit - more elaborate V2 added. ...Adds some holes for self tappers to increase stiffness, as well as some ribs.

This is a fixed version as the original clashed. ...I could not edit that "Thing" so made another. See a photo of it in use on my Ender Pro with 2x MGH12 Rails.

I made this part to convert my Heated Bed to Linear Rails. This should work with most 6 wheel printer designs. I and rework the hole pattern if you send me the hole dimensions. ... https://www.youtube.com/watch?v=fKDs7HW3cAE Liner Rails I Used...

I took the gears, bearings and such from a BMG extruder I was already using on my Ender 3 Pro and I used these sensor parts from Amazon: https://www.amazon.com/gp/product/B07PYQWGK1 Print instructionsSupports will be needed for the Fan Mount, the...

... a bit more, but so far the test prints I've made seem pretty good. I took the gears, bearings and such from a BMG extruder I was already using on my Ender 3 Pro and I used these sensor parts from Amazon: https://www.amazon.com/gp/product/B07PYQWGK1

Additionally I made some alterations to the bolt holes and overhangs to make it more FDM friendly and reduce the need for supports. I consider it a WIP as I am still working some bugs out regarding the filament sensor, but I think those issues are...

Remixed Into Thicker Belt Clamps.