line tamer 3d models

 Add washers if the clamp is disassembled/reassembled fairly often. To create stackable clamps for parallel pipes of different sizes, the clamp for the smaller pipe needs to be the same size as the one for the larger pipe so the bolt holes...

I found the best location was in-line with the left Y-rail. You can do this later, but it's easier without the bed in the way. https://cdn.thingiverse.com/assets/a3/25/49/3e/6d/2021-03-14_10.25.35.jpg ...

The bottom line, is that if you do the math on ordering the parts yourself and include shipping, you will have a hard time beating the price of their kit. You can order the MakerRx Furious kit here:...

Done.As with all vase mode prints (especially printed with 0.4mm nozzles) I recommend increasing the line width and also the extrusion multiplier by a bit. Setting “Infill/perimeter overlap” to something like 35% also helps to ensure that the walls...

This is because we used cura to do the slicing and the 45-degree angle makes the infill structure line-up lengthwise with the part, which seems to work slightly better than other angles. To print as fast as possible, we used 0.25mm layers, 20%...

Ensure the BIOS switch is in the correct place when you reassemble the keyboard so it lines up with the actual switch. **THERE ARE 2 HIDDEN SCREWS TO TAKE THE BOARD APART, 1 UNDER THE LOGO ANOTHER UNDER THE RIGHT VOLUME KNOB COVER** That massive...

... out the river water layers and fill in some gaps in the roofs. Mod Podge actually works quite nicely for filling layer lines. ...   Good luck to all entries and hopefully all these great designs can show off just how awesome TownBuilder really is!

So this is the most troublesome to use, but if you have errors, try to:set a different (lower) bend angleset a larger bend radius, or try to reduce the error-inducing fillets radii, or eventry deleting unnecessary fillets from the time line...

Run the sensor and power lines through the wire channel. Position the LED ring into the base and solder the data, VCC, and two ground wires. Put a zip-tie around the power and sensor wires so that tugging on them won's put strain on the solder...

DO NOT print the mounts 'bottom down' for the layer lines will become a weakpoint in your base and you can lose the gopro. Highly recommend washers on all mounts, RDQ has nice countersunk ones. I try not to add extra things I dont need to my quads,...

The 5900 model was the top of the line bike that was ridden in the Tour de France in 2003/2004 and cost over $3000 in those years. This is NOT designed to fit Trek's OCLV 5000, 5020, 5200 or 5500 series frames/forks. *** The headset on my...

This will be to tie a length of Kevlar line that goes to the parachute and nose shock cord. Bore the hole as close to the top ring as possible. 2mm or 3mm max. I have started putting a drop of CA on all Kevlar knots - I had two unravel on the same...

Note: Purchases and printed items will go together often times, so I'm putting in the printed parts with the purchases on the same line. Printed - Y Belt Tensioner (https://www.thingiverse.com/thing:2747511) - X Belt Tensioner...

The robot has a ponderous gait.   PrintingGenerally I use a 0.25mm layer height and put about 1mm of plastic on the outside surfaces as a shell.  Since my printer has a 0.5mm nozzle I use 2 vertical shells and 4 horizontal top and...

Notes on my accelerated printing settings: =========================================== I have my printer's stock hardware (with 0.4 nozzle) using tweaked slicer settings that not only emulate a 0.6 nozzle, but also increase movement speeds (both...

Gems shine forth with unparalleled allure: on the Engagement Ring, precision-crafted details are nestled among slender lines that dance across its expanse: tiny studs precisely positioned at calculated distances - 4.3mm, and diminutive loops...

**Type 5**...

Or you can just use a commercially available metal buckle (or recycled from an old band) if you want to be extra safe. Other features:You can make a watch strap without the pattern, set the Pattern_thickness parameter to a very low value (see...

When all 4 pairs are in then with some wiggling you should be able to get everything to line up with the top piece and click the pillars into that one as well. If you would like to keep up to date with my latest work, follow me on...

However, there are indeed many flaws with this original design and process, tinkercad has a tendency to leave small gaps and unwanted artifacts in the final .stl exports, also the curved line ability in tinkercad is very limited and results in split...

Now you connect the bridged L/R and GND from the BT board to line in (IN-L OR IN-R and GND) of the amplifier (if you are using a stereo amplifier, connect to either the left OR right channel). Finally connect the output from the amplifier (L+ and L-...

Chūshin-sen Chūshin-sen (中心線, center line). The term is also associated with kendo. Ichi-go ichi-e Main article: Ichi-go ichi-e Ichi-go ichi-e (一期一会, one time, one meeting) describes a cultural concept often linked with tea master Sen no Rikyū....

Full description about the FW and downloadable files here: https://github.com/kisslorand/BTT-TFT-FW If you like the extra work done or if you want to contribute to further improvements you can buy me a coffee here:...

Solution: change the code a bit if (y == 9){ digitalWrite(a, LOW); digitalWrite(b, LOW); digitalWrite(c, LOW); digitalWrite(d, HIGH); <----change here to LOW digitalWrite(e, HIGH); digitalWrite(f, LOW); digitalWrite(g, LOW); And a few lines below if...

As it gets closer to the joiner piece line it up with the faces of the top plate and screw them on together. Screw it only finger tight initially. Now take a 17mm spanner and hold the nut on the bottom of the basket and gently tighten the top plate...

The line pattern on the yellow container was Designed by Freepik. The triangular pattern was remixed from a design by <a href="https://www.freepik.com/freepik">rawpixel.com / Freepik</a>. The floral pattern was remixed from a design by <a...

Even raster line colourization like known from the C64 demo scene are possible for the overlay mode. Even the shelf's got independent configurations, so they can be all on, take the color of the clock segment above or only one group is randomly...

If I print 3 wall lines, one string hangs into the gap, but is easy to remove with a small v-shaped knife. You should have a 2nd view on the wheel bearings, they should run soft but I had problems printing a perfect bearing, V16 seems to solve...

I soldered them to the speaker and put a jst connector on the other end.Step 2: Front UnitThe front contains the GPIO Buttons, that are mounted to the quarter sized breadboard.To solder the buttons i used a common ground for all buttons and soldered...

the object here is to reduce the layer lines and heavy marks to prepare to fill the imperfections.You will see how good your layer alignment really is in this stepDisassemble and Fill all the surfaces with glazing puttyDisassemble the top and bottom...