lightsaber holder belt

Klemmbaustein Saturn V - a simple small Wallmount
thingiverse

Since I don't want to entrust the enormous weight of this rocket to simple plastic, the floor holder has been specially designed to hold a metal bracket that supports the weight of the rocket. The angle must not be wider than 20mm and thicker than...

Snaggo' - A lipless 3d printed lure
thingiverse

****After modifying a couple prototypes with suggested mods (one with a lip, and one with a top-mount line ring) I found them to have terrible action, either fighting the lip or fighting the line holder. I'd recommend adding weight to the front of...

Convolution - Interlocking puzzle by Stewart Coffin (STC #30)
prusaprinters

...Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work.Our puzzles are modeled using the open-source puzzlecad library.

Superstar / Third Stellation - Interlocking puzzle by Stewart Coffin (STC #50)
prusaprinters

...Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work.Our puzzles are modeled using the open-source puzzlecad library.

Patio Side Table
thingiverse

My glass measures 11.75"x11.75" so with the 8.5" rails this fits the size defined for the glass corner holders. This is important as these corner pieces need to be pretty close or they will not clip the glass in place properly. If the glass top is a...

Old Factory Building Interior Set Collection
thingiverse

For power I used 3xAA battery holder with a switch. SAFETY FENCE: Print using a resin printer at 5% scale. Paint in safety yellow or silver. ROOF SUPPORT 12mm TUBE: This is used to support the roof where required. The ends are based on the...

iPhone X (with case) bike mount - flex
thingiverse

So, I lengthened the holder to get it closer to the center of gravity. I designed this from scratch using plain old AutoCAD 2016 Not yet printed. I plan to use TPU (Ninjaflex) or something like it. * 07-02-18 - Update: Printed and used... First...

CR10 All-In-One
prusaprinters

case and mount for the control display, and new display cable from Amazon (update April 1, 2018) Added STL for spool holder. (update April 13, 2018) Adding cover plate for the remaining area of the printer, which includes: a cover plate with...

MisteryBox / Useless Machine
cults3d

... parts as a kit Engine - approx 0.90 ? - link Switch - 0.35 ? - link Limit switch - 0.24 ? - link 4AA Battery holder - 0.48 ? ...- link wire AWG #24,#28 - 80 cm approx bolt M3x8 - 5 units bolt M2x7 - 2 units lag screw 3x16 mm - 4 units (+4 more)

NOS Burr Series - Interlocking puzzles by Gregory Benedetti
thingiverse

Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work. Our puzzles are modeled using the open-source...

Staggered Target (Nerf target practice)
thingiverse

We can then use a simple Cube object to create a cut in the face for the pivot (holder) for this target face. The resulting cut will allow us to build an arm to hold up the face and pivot from the base. You can use the techniques as described in...

35mm Film Crank Winder
prusaprinters

Two of the five variations have taller winder heads, and the "uni-crank" is an attempt to merge the "top" and "bottom" cranks into a single unitThe crank arm is wider, so as to more aptly join to the winder head, since the original was too thin for...

Ender 5 (Plus) Hemera Mount Hardened + BLTouch + Cable Manager
thingiverse

I've been using the holder for over two months and it hasn't bent in any way ... finally! I hope you enjoy sharing and that it can solve your problems as it solved mine, now I can fully appreciate the Hemera! BLTouch Offset setting { X, Y, Z } ...

Ender 3 Pen Plotter Mod
prusaprinters

This acts as a compressor and stopper for the spring to preload tension.Watch this to load Pen into holder   https://youtu.be/mSTqH0C04FgThe guides keep the springs compressed, the pen as vertical as possible with little to no movement. The...

Filling machine "Hanimandl"
prusaprinters

The holder for the servo motor is firmly connected to the squeeze tap. Control unitAll operating elements and the corresponding microcontroller with display are located in the control unit. The housing consists of an upper part and a lower part,...

2D Level Fixture
prusaprinters

One has to stop drilling for reading the levels, but it really avoids that you drill anything else as a right angle. Print instructionsCategory: Tool Holders & Boxes Summary Today I needed to drill eight holes in the ceiling, so I decided to buy...

Plants Set 1 3D model
cgtrader

This is a stunning set of 6 house plants carefully selected from the esteemed PoserWorld collection, designed to instantly enhance your kitchen, garden, or interior scenes with an unparalleled level of vibrancy.\n\nProduct Features (Poser):\n\nThis...

Voron V0.1 CR10 Hotend (Mini Afterburner mod)
prusaprinters

The dimensions of every CR10 hotend should be compatible but the default (non-"all metal") hotends are designed to be used with a bowden tube inserted deep into the cold side, which is a problem for this mod.Other mods on my Voron V0:The Ultimate...

VaDiM by Solaris
prusaprinters

the axel and bearing's inner roller must form a fixed subassemby, and the outer roller of the bearing is simply held in place by the holder's geometry (has it has a rim on the outside, so once assembled the bearings physically can't come out) I'd...

Square Knot / Plus 2 - Interlocking puzzles by Stewart Coffin (STC #9 & #57)
thingiverse

Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work. Our puzzles are modeled using the open-source...

PEREUKA Keychain Multitool - Customizable
prusaprinters

And what use would a bit socket be without a…Bit holder - it fits a standard bit snugly, but just in case it wears out with repeated use, it also has space for two magnets that should keep the bit in place.MORE MAGNETS - extra four holes for magnets...