lighting a 3d model

Frame made from 68 mm center distance polycarbonate with a mini racing Evo SP flight controller. It is fully configurable and cleanflight on all flight modes. FC: Banggood's Eachine Tiny 32-bit F3 Brushed Flight Control Board Based On SP-Racing...

Thank you once again for giving me the opportunity to help, and I hope we can collaborate successfully in the future! assistant It was a pleasure assisting you, and I'm glad I could be of help. If there's anything else you need or if you have any...

# Customizable Skadis Drill Bit Carousel This is a custom parametric design for an Ikea Skadis Drill Bit Carousel, offering multiple parameters for customization. It is based on the remix of [Ikea Skadis Dril Bit...

One upon a time, after Russia's secret nuclear deterrence programme "Vjuga" (blizzard) but before deployment of the Dead Hand nuclear missile defence system "Perimeter", there was first silent eye in the sky, manned by long stay crew of two. This...

Customized Version of Thingiverse's Phone Case Creator Tool Created with Customizer, an Online Tool Found on the Official Thingiverse Website Instructions to Create Your Own Unique Phone Case: Using the Following Options: pattern_element_radius = 8 -...

The partition is divided into an integral type and a part type, so print them according to the printer. And I uploaded wordplate and word separately for multicolor users. I'm not sure this is because I haven't tried Single nozzle users, please...

PRINT SIZE: 290x290x340 (with BLTouch Sensor mounted) All screw needed for this build is basically from the Flsun cube printer with extra screws already used from the printer, so there's no need to buy a screw to build it. MATERIALS GT2 Closed...

I have custom made all these textures at a high resolution of 4K, and I hope you will find them useful in your own projects. ... Texture Category: Building Sub-Category: Bricks Texture Type: Seamless File Type: JPG Dimensions: 4096×4096 (4K)...

Two gears interlocking seamlessly assistant A set of gears fitting snugly together Une garniture de engrenages s'emboîtant parfaitement Dos piñones engranados juntos Dvoje zubnih kočnika zalijehani Два зубчатых колеса, соединенных между assistant...

If you want the base to fit a different casting please send me the dimensions indicated here: https://imgur.com/5T6mb2L The hole for tying the car might be small for Hot Wheels but I don't have the exact car for Hot Wheels to test it out. The...

I made following mounts: - horizontal for 38mm tube (outer diameter about 47mm) - vertical for 38mm tube, low - vertical for 38mm tube, high - horizontal for accessories, diameter up to 30mm - double-hook for accessories Each parts are uploaded as...

It took a few weeks to print mostly due to filament jams I was having....After switching to 100 percent infill for all the torso parts but the helmet, I was able to get it all printed. This build is about 18 inches tall with hands not raised above...

Human: FAQ: http://www.thingiverse.com/shivinteger/about Generating Attributions log: Thing Title: VirtualRobotix VBrain AutoPilot Enclosure Thing URL: http://www.thingiverse.com/thing:32321 Thing Author: virtualrobotix Thing Licence: Creative...

Digital Voltmeter (this one bad idea try to find a better one) https://aliexpress.ru/item/32693996957.html?_ga=2.96398620.1020419603.1638803910-1968376420.1580139662&sku_id=64488646259&spm=a2g39.orderlist.0.0.6aa54aa6D1r2x4 9. 10K Linear...

Currently I found no possibilty to adjust these intolerance, so I have realize a tool to do so. With this tool you can adjust the angle between the 2 pipes of the Primo Core to exactly regulate the pipes to 90°. The Tool is partly built on the...

... although some parts still warp on the edges. There is still a lot of draft around the heated bed, coming either from the power supply or the mainboard fan. ...However, some test parts printed with sharp corners and negligible warping.</font>

Put a little contact glue to stiffen them and screw them together. Step 3 Insert the 25mm diameter pipe through the two backing clamping pieces and backing sliding pot 1 and 2. Try not to fit all eight tubes until you have attached the backrest to...

A. Lüftergehäuse mit Damperanschluss - 4 x Zylindermagnete Durchmesser: 4mm,Länge empfohlen: 5-6mm (Magnete können auch kürzer sein, das Loch ist 7mm tief und sie müssen eingeklebt werden) ...

Currently I found no possibilty to adjust these intolerance, so I have realize a tool to do so. With this tool you can adjust the angle between the 2 pipes of the Primo Core to exactly regulate the pipes to 90°. The Tool is partly built on the...

I'm pretty sure the back support is at the correct height, but a sliced/partial print should still be done to confirm. The cabinets will likely now need supports are otherwise be rotated to print properly. Note: I saw in one of the remixes that...

**Print Settings:** * 100% infill * 0.2mm layer height * Use PETG or ABS filament * No support is needed **Parts List:** * Four M3x6 screws for the x block * Sixteen M3x8 screws for the linear rails and y block * Five M3x12 screws for the y belt...

Join us on Patreon - click here!- 25% discount on MyMiniFactory for each patron- 50% discount on MyMiniFactory on selected miniatures (changes monthly) Join us on Kickstarter - click here!- On ongoing campaign you can find better deals for bigger...

In search of a better solution, I experimented with indirect reading concepts from Thingiverse and the Duet forum, utilizing bearings. However, these attempts were not always reliable due to the bearing surface's lack of grip on the filament. This...

If you enjoyed this project please share your make, leave a Like and Collect for the community or post it on Facebook or Instagramm To show your acknowledgment and support for my large Effort on this you can donate via PayPal. janoerter@web.de ...

With a 0% complaint rate, 1st place in re-purchase rate, and 1st place in recommendation rate, our company is trusted by customers for its reasonable prices and honest sales approach. We will always think from the customer's perspective and sell...

I also had a version with threads included, but it is impossible to work with and render it. ## Currently implemented parts and assemblies: * Diamond Hotend Nozzle [doc](http://reprap.org/mediawiki/images/7/73/Diamond_Nozzle.pdf) ... does anyone...

(siehe Fotos) This is a connector housing which was often in use by east german computer producer robotron. Printed in with Ender3 in super quality (0,12mm). ...Turn the lever on the most flat side and use supports from plate.</p> <hr/> <p>FreeCAD...

Soldier for the Naboo security forces is a powerful force. ... 1/46 Legion scale For more Legion scaled stuff, check out this: Royal Naboo Security Forces ---------------------------------- VEHICLES: HEAVY AAC-1 Speeder Tank...

If you want to recreate this you'll need the following things: -transparent filament for Playstation logo -black (or colour you want) filament for the lamp case -on/off snap in switch...

---------------------------- The bracket can be mounted independently in conjunction or as a complement to other components and is used to attach the 7 inch to the upper ALU profile of the printer. Mounted there, the display takes no space on the...