lian li offset bracket 3d models

It is specifically designed to have zero (or close to zero) Y offset from the nozzle (read below for explanation). On my printer the offsets ended up being X=40, Y=0, Z=-2.02, though this should be measured per installation. ...Printed in Overture PLA,...

This is a very basic bracket to offset a 15mm thick table by 45mm. ...I have also added a hole for a screw to be added (3mm in diameter, so look for screws less than 15mm in length with an inner diameter smaller than 3mm), but this holds on just fine...

... to clear clips on the build platform. Print the offset bracket in PLA using .25mm layers at 20% infill (standard settings) on an M2, after cleaning the STL file with Netfab. ...Replace the original fan bracket with this one for improved positioning.

Simple straight front bumper mount for SCX24 C10 I designed this because I mounted my body higher to create more clearance with the tires, but flipping the stock bumper bracket put it too high, so I designed this zero offset bracket to create more...

What makes these brackets unique is that they mount on one side of the corner and have a little bit of an offset. The feet of my laser basically go from edge to edge of the 2'x2' plywood, so I needed to mount the brackets on the side of the laser...

This is a motor mount offset bracket for the Zohd Dart 250G which allows you to install a split camera and a 3S Lion battery in the fuselage while still having room to move the battery forward and aft in order to get the correct CG. The 250G was...

Bracket for the Creality Ender 3 which offsets the y-axis limit switch forward to account for reduced travel due to stepper motor dampers. This bracket uses standard hardware to attach to the y-axis aluminum. I opted to use two holes instead of a...

Runout sensor offset for the Creality CR-6 SE or CR-6 MAX printer with a metal extruder.

Offsets stock screen to the right 40mm, leaving so much more room for activities.I needed to move the screen so I can easily tram the X rail to the base with spacer blocks. I tried one I found on here that wasn't sturdy enough for my liking, so...

This bracket is specifically designed for the Olympus E-M1 Mark II in order to allow the mounting of a Rode VideoMicro when using a gimbal in order to avoid collision of the microphone with the gimbal in underslung mode.

This is a custom bracket designed to secure the filament holder in place, addressing a common issue where certain spool designs with narrow center rings tend to shift or move under the printer's print bed during operation.

The design utilizes the existing metal bracket from the Ender5plus and an extremely well designed spool holder by Skrutt84 "Ender 3 - Filament holder DELUXE" https://www.thingiverse.com/thing:3114139 Parts: (2) M5x20 screws w/ bolts (6) M3 screws w/...

you'll need two of the things - they are exactly mirrored.had to cut it based on the build volume of my genius. a little CA glue in between them, two screws to the bottom of the case, two screws to the middle fan. ...works like a charm :)

Made to slide over the 2x 120mm fans at the bottom of the case which blow onto the GPU

Revised version of the first one. Slightly longer for flush alignment, slightly thinner to avoid putting any pressure on the glass. ...Slide up into the gap between the metal chassis and the glass and it should stand on its own.

Wanted to mount 5" Raspberry Pi display that I had been using as a sensor panel to the back of my O11 Dynamic Case. Screen: https://a.co/d/2CVXOje Screws + inserts from McMaster Carr, part #s: 10mm* M3 screw (need 10 screws, sold in packs of 25): ...

Remixed the 80mm fan shroud by PROPWURX to be completely closed as I don't need the fan and just wanted it as a cover.

Helped with temps. Your mileage may vary depending on your layout. This was a test run to check if the concept would even work. Fans used: 1 * 120x25 Silverstone Airblazer 2 * 60x20 at the bottom row 4 * 40x20 at the bottom row 4 * 40x10...

100% ready to cut.Perfect sizes.Enjoy.;)

There's a couple commercial options for an airflow focused panel for the o11 Dynamic XL, but they're expensive. Other panels on thingiverse are all for the o11 evo or standard. So I made this, it's designed to fit on a CR10 or similar sized printers....

I've got my old HTPC back online and decided to turn the Q07B-Case into a usable system. The Q07 has two major issues: * The ATX PSU is mounted in a way that restricts airflow. * Airflow inside the case is almost non-existent. To address these...

Hello, this one is a drop in shroud for the big 360mm radiator Space at the front. I didnt liked the original fan mounts so i created a cover, which you can also use to mount things to. The thing in the middle is not necessary and only used to...

Wanted to hide as much of the (already very minimal) cables from the UNI Fan setup. ...Should be enough clearance but haven't tested with many motherboards yet.

Print X-side on bed Mirror for L/R Designed for M3-8mm, M4-12mm, and M4 D7H5 heat-set inserts

textures are now included

After I´ve created a Remix of SirCBO Design for the Dynamic XL I was done with it and only used it for Cables.... Meanwhile I´ve changed a lot in my System and I am Planning to lead my softubes to the backside of the Case and from there to the...

Descriptiontextures are now included The 3D model was created custom. we created it low poly to used in games, short films, animations, youtube templates, and soo on. Model formats: ANIMATED - This model has PC starting animation of RGB turning ON,...

Replaces the white LED PCB found under the interchangeable pump cap on GA II Trinity AIOs. Uses the 3 screws that come preinstalled. ...I made this to fit in an A4-H2O but it can be used in any application where vertical space is at a premium.

This thingy centers the Strimer LED stripe on RTX 3090 FE + hides the 12 pin cable. ... V2 * improved stability * improved fixation V3 * better fitting