lian li o11 mini distro plate 3d models

watch out for dust! ... strongly recommend petg or other materials with higher plastic temperature, if your pc temps are high (which they probably are if you need ventilation like this)

Spacer for 2 slot graphics card to move the graphics card outside. Better ventilation especially for Founders Edition from Nvidia. ... Better ventilation from behind and fresh cold air from outside.

watch out for dust!

Thesse are cable combs, 8 wire, 4 wire, and 24 wire for strimer plus RGB Cable mods.

Done and tired with losing my work over my cat stepping on power button, so this is my 2nd project with Fusion 360! ... Enjoy!

This is a PSU cage that will allow the power supply to be offset from the side panel of the Q58 SFF case, and also allow multiple vertical positions.

This is one of the most popular bay module to get the power button, reset, light leds, usb hud, etc.

Spacer for the SSUPD Meshilicous Case, to mount the glas panels with an offset. Still WIP and not tested with the panel. ...Just the fitting.

Chun Li Mini at a negotiable price; submit your best offer! Proceeds fund our artists, enhancing future models. Typically, our projects cost $20-$30 each, hence the $33 price tag—a donation of about $20 enables an artist to start a new project. Our...

Dual 60mm fan mount to cool your HDD/SSDs on the LianLi O11 XL Just attach the fans like shown in the pictures and route the cables through the grooves.

Take a minute to watch the video I made for this mini figurine on my YouTube channel: https://www.youtube.com/watch?v=33Npl_AwJdY If you'd like to support my work, visit my Patreon page here: www.patreon.com/worldofminis Thanks and I hope you enjoy...

He had the LI plate topper! I didn't have my Revopoint 3D Scanner with me, but I grabbed a quick photo. I used the imagetostl.com website to convert the photo into a quasi 3D model. I was able to load this into the Geomagic DesignX CAD software and...

I designed this display mount for my Lian Li O11 Dynamic XL You have to screw the mount first on a 120mm fan and then attach the display to the mount and then put all of it into the case as one unit. the Display is mounted in a 25 degree angle for...

To create this unique item, settings such as width (50), indent (5), font (write/orbitron.dxf), edge (5), radius (15), length (100), holeRad (5), and text properties like line1 ("T.S.A.") and line2 ("Agent Li") were used. Additionally, the build...

Made to slide over the 2x 120mm fans at the bottom of the case which blow onto the GPU

One of the clips of my PC case broke so made a replacement for it. I believe the clips of all Lancool cases are the same but I cannot say for sure. The walls are slightly thicker that the original clip since I wasn't sure my PLA was strong...

I've got my old HTPC back online and decided to turn the Q07B-Case into a usable system. The Q07 has two major issues: * The ATX PSU is mounted in a way that restricts airflow. * Airflow inside the case is almost non-existent. To address these...

This thingy centers the Strimer LED stripe on RTX 3090 FE + hides the 12 pin cable. ... V2 * improved stability * improved fixation V3 * better fitting

I wanted to mount my 5inch screen in the rear of my case and I noticed there was a bracket above the PCI slots that I dont know anything about, so I made it a mounting bracket for my screen.I also made sure there is full access to the SD card slot.It...

Replaces the white LED PCB found under the interchangeable pump cap on GA II Trinity AIOs. Uses the 3 screws that come preinstalled. ...I made this to fit in an A4-H2O but it can be used in any application where vertical space is at a premium.

Helped with temps. Your mileage may vary depending on your layout. This was a test run to check if the concept would even work. Fans used: 1 * 120x25 Silverstone Airblazer 2 * 60x20 at the bottom row 4 * 40x20 at the bottom row 4 * 40x10...

Revised version of the first one. Slightly longer for flush alignment, slightly thinner to avoid putting any pressure on the glass. ...Slide up into the gap between the metal chassis and the glass and it should stand on its own.

Tossed together a b style standoff for my lancool since i snapped two off while cleaning my computer, then snapped off another seeing just how brittle they were x) Printed standing upright with and without supports... and supports on base only...

... has been accurately determined as 2.45 units. Ring height stands at 6 units tall. Pin cap width measures precisely 4 units. Build Plate Type has been set to type zero. Element: Lithium. Build Plate Manual Length is carefully set at 100 units.

Barrow Distroplate for P600s and Evolv X PHP600S-SDB 99% accurate

Barrow Distroplate for P600s and Evolv X PHP600S-SDB 99% accurate

This is a Barrier to mount onto the Drive-Tray on the side of your Lian Li O11 Dynamic. I used 4 - 4x12 Universal Screws through the holes of the pre-mounted rubber dampers to fix the pieces in place. There are 3 wire-ducts for the Fans. 2 Part...

Customized version of https://www.thingiverse.com/thing:834725 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=834725

Customized version of https://www.thingiverse.com/thing:148722 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=148722