lian li drive cage 3d models

I'm simplifying my 3-drive enclosure to a compact 2-drive setup.

This model is meant to house 16 drives in total, 8 per side with 3 80mm fans per side cooling them.In between the towers there is space for a standard sized power supply.This model is a work in progress and is not ready for use at the moment.This...

This model is meant to house 16 drives in total, 8 per side with 3 80mm fans per side cooling them.In between the towers there is space for a standard sized power supply.This model is a work in progress and is not ready for use at the moment.This...

Customized version of https://www.thingiverse.com/thing:2482372 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2482372

Customized version of https://www.thingiverse.com/thing:3198330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3198330

Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573

Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573

Customized version of https://www.thingiverse.com/thing:1220978 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1220978

Customized version of https://www.thingiverse.com/thing:714444 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=714444

Customized version of https://www.thingiverse.com/thing:148722 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=148722

Customized version of https://www.thingiverse.com/thing:834725 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=834725

This is a compact housing unit designed specifically to accommodate three point five inch hard disk storage devices.

Then the parts are assembled using inserts and screws to form a cage for 4 external hard drives (3.5"), with a spot for a 120mm fan or a 140mm fan with an aditional plate. Drives are on flexible cushions to absorb shocks and vibrations, and a spot is...

Hard drive cage for Antec P180. This is for the top drive cage slot. Use PC fan screws in the top and bottoms screw holes for alignment, and epoxy to hold all pieces together. ... Items to print: 1x top piece 1x bottom piece 2x side pieces Printable...

this is a back wall clean up and drive cage delete for the XPG Battlecruiser PC case. ... I printed each print with no supports and 20% infill.

If you remove the metal cage and replace it with this cage, you can install 2x NVMe and a SATA hard drive. The only drawback is that the second hard drive cannot be reinstalled due to the lack of space. Therefore, I would not recommend installing a...

This enables you to install two SSDs into a Sharkoon hard drive enclosure, perfect for utilizing the 2x3.5" cage to hold up to four SSDs. Simply remove them like a drawer if needed. The images depict an older version without notches on the mounting...

I haven't found a printable 3D model of the drive cage for several Fractal Design cases, so here it is. I haven't printed it personally because I don't need it. I just modeled while it was out of the Meshify 2 case I just bought because I'm waiting...

Let me know if there is something wrong with it.If you need the drive tray, get it here: https://www.thingiverse.com/thing:4487637  I used that tray to model my cage, but it should also fit the original metal trays.Print it face down and you...

With five of the cheapest possible 120mm fans, the hottest drives in my case are 53 C and the cage is stable even in PLA. I worked hard to get this design under 500 grams, so you should be able to get two out of a fresh roll. I've found that the...

... drive to be mounted upside down since the tower stands upright instead of on its side. This clever solution enables the drive bay door to swing open from top to bottom, eliminating the frustration of it swinging down when trying to swap hard drives.

I needed to mount two 3.5 in Drives in this chassis so i made this printed off three times to get it correctI used a couple of wood screws to secured in place With some 3D printed things

... minutes and uses about 195 grams of filament. To assemble the replacement hard drive cage you will need: - Four M3 screw inserts - Four screws measuring between 6mm to 10mm in length - Two short screws with a flat head, each only 5 millimeters long

Fixed the tab on the bottom to match the case

<p>Requested remix for sidepanel adjustment to fit some higher cooler / pumpblocks in the SSUPD Meshilicious.</p> <p>NOT TESTED from my side.</p> Category: Replacement Parts

customized with 3D Slash!

customized with 3D Slash!