levitating floating bed 3d models

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

* Allows a customizable bracket to be inserted to hold an auto-bed-leveling (ABL) sensor. * Four such brackets already provided in a separate STL file. One of them is a dummy bracket to fill the space under the Z-19 when no ABL is used. The other 3...

The curved part is inserted in the hub and the flat part that was on the bed is visible. 7 - All items in the console are 3D printed, optional decals are attached to the sides of the model. A JPG file containing the decals is included in the...

At minimum at least do some calibration on the extruder etc, PID tune, bed level etc. You'll suffer print quality with loose belts so maybe MacGyver it until you can get these parts to get your belts tight! Printed on PLA but will be printing this...

 I reprinted the part with a raft and it fit much better)3 - Optionally, for an optimal joint between the hat_bottom and the hat_band, the top layers of the hat_bottom can be printed at a lower layer height to help smooth it out a bit.4 - When...

But if you cant make long prints like me because you have your printer in the bedroom or likewise, you can choose the print it in two halves you need will just need to print two connector pins as well to make sure the two halves line up correctly.I...

On a MK3S+, you can print up to 12" rails, but I chose 8" rails since it's easy to fill the whole print bed.Next, print a bunch of crossties (crosstie.stl). 0.3mm layers. They should be printed edge-on so the “clamps” are able to bend without...

This is designed with a chamfer on the side facing the print bed and a fillet on the top. It makes a nice looking contoured part that prints without any supports. If you have your first layer elephants foot compensation perfectly dialed, maybe detune...

I had no vise available for this little project, so my wires are not really straight…Add the 12 silver copper wires to the 12 channels/holes as shown and fix them in the base like shown.Make sure not to make the wires too tight because the M4...

With a heated bed, hot extruder, and cheap power supply, there's a lot that could go wrong. I have worried about leaving my printer unattended and wanted an automatic smoke detection and shutdown solution. This post contains all the information you...

I intend to mount a PiCam on the bed carriage where there's a couple of screw holes conveniently unused for the cable chain on the rear of the printer. To this end, there is a small slot in the base for the PiCam ribbon cable to exit. The V3.1 box...

&nbsp;It needs supports on the print bed only. I added a support blocker around the digit 5 to avoid messing up the clock surface.</li><li>I printed the hand holder parts (tube and disk) all separately to minimize stringing.</li><li>The molten clock...

## ABOUT THE DESIGN ## I wanted a design that gave a smooth airflow and balanced transition from the round profile of the fan to the square profile of the hot end while not impacting access to the extruder nozzle for bed leveling so I placed the fan...

I would suggest all parts near to the hot end and bed should be printed in PETG whilst others will be fine in PLA if sufficient layers and perimeters are adopted. The black parts are ABS, the ABS parts were printed with no cooling and a 10 layer brim...

print with tree supports!!!TOP - right side up (same as it appears in the final stand)MIDDLE - right side up (same as it appears in the final stand)BOTTOM - right side up (same as it appears in the final stand)2 END CAPS- I printed this what the long...

5mm higher, which shouldn't matter because it doesn't sit on the heating bed while engraving. At the end I thought about it, if I'm tinkering about, I add 2 LEDs for lighting effects that come on when the hotend is cooled. I soldered the whole...

Nozzle 0.4mm Layer 0.1mm Infill 70-80% The fixing screw holes are 3.4mm (Model, + tolerances (through nozzle diameter)) I have with my hardened holder ABS geruckt (bed 113 ° C), no delay to determine. YouTube link (Topic: PLA annealing for more...

Just look at following pictures, its clear, how to place them on the bed.The only item that needs supports is “Healing potion” ("big shield" if you know Fortnite).To finish items, use some glue to put them together. Use piece of filament as an axle...

... have problems with warping. The brim tends to keep parts from lifting up from the print bed.Most other parts should not necessarily require the usage of supports or a brim. ...In all cases it won't use much filament at all, so it should be fine.</p>

PETG or bust for this piece due to proximity to high-temp components (not only the hotend but the bed as well)Extruder Motor Cable Chain Mount bolts onto the pre-existing plate. Pretty self-explanatory, and is where all the mounting hardware is...

1.8m, it's a really big model, divided in 18 parts per level, and needs to be printed with 35cm bed printer. Since bigger printers are becoming more popular, I decided to include this scale. Also, the Amongusers can be made in this scale, and use it...

Be carful that you fully overlap the original top part.3D Print:1* cap* innerRing* outerRing1* mainBody1* usbStickCase11* usbStickCase2These parts doesn't require support, but I printed them with a brim to secure them safly to the print bed. I...

 Oh yeah, there are also some cable routing clips you can bolt onto the struts! Print DescriptionAll the parts here are intended for straightforward printing, nothing tricky!Print DimensionsThe main thing to be aware of is that the screen case itself...

You can also double up and use 2 drawers on top of each other if desired.Specs:Holds 48 bottles of paintTracks for screws to secure it to the shelf unit if you want to make sure that you don't accidentally pull it out too far5 OpenLOCK clips to...

--------------------------------------------- Other Changes and Refinements --------------------------------------------- --------------------------------------------- 1) The population cube tray was split into two parts (four parts if you are...