level ender 3 v2 3d models

I recently bought an Ender 3 V2 to start exploring the wonderful world of 3d printing, but I live in a studio, and my printer is located right beside my desk and around 3 meters from my bed. The Ender 3 V2 is VERY SILENT, so I didn't have any...

#### RIBBON CABLE MAY BE TOO SHORT TO BE USEABLE #### #### Very Close to Y-AXIS #### This is a screen mount I designed for the Ender-3 V2. I wanted to be able to adjust the angle of the screen to be seen more directly to where I work from. The mount...

Filament guide for Ender 3 V2 (maybe it works also for the other Ender 3), it simply snaps above the x axis motor without any screw. The bearing (is the one of the stock extruder) snaps easily in place without screws and should move freely. It must...

This is a simple cover for Ender-3 V2 LCD display. The [Creality Ender-3 Logo](https://www.thingiverse.com/thing:3078936) on it was made by [tom666](https://www.thingiverse.com/tom666/designs). Thanks to...

Filament guide for an Ender 3 v2 printer. Most likely works with the original Ender 3 however it hasn't been tested. Sized for a 608 bearing and a m6 x 25mm bolt. To fit properly, the bolt head for the upper Z carriage roller must be on the...

This is a scraper holder for the Ender 3 and Ender 3 Pro 3d printer.

This is an accessory for the ender 3 v2. It fits right over the belt tensioner bar and dispalys the ender logo. Tried to find one of these, but couldn't so I just made one. Hopefully it will make it easier for you. I have included 2 designs, one with...

They fit the end of a 20mm European extrusion on the left side of the Ender 3 V2 top rail. The filament guides use a standard pressure fitting and a 60mm length of 4.00mm OD PTFE tubing. There are two models of the filament guides, one with a tang...

Based on MartinDubois' project (Tool holder for Ender 3 v2) I made some changes to add a USB adapter holder. ... The spatula and USB adapter holder is placed on the horizontal frame of the printer and is not disturbing at all when printing, while it...

Simple BL Touch mount for Ender 3 V2, using 2 pcs M3 Screw STL parts are pre-orientated for easy print and good results Additional parts needed : M3x6 Button Head/ Hex Screw 4 Pcs M3 Nut 2 Pcs Probe offset for the firmware: X-42,Y-5 Original Creality...

Also my calipers didn't fit right :) My model is tested with Ender 3 v2 only, without the right side display, because mine has been moved to the left. ...Also, my printer is raised because of the improved cooling, otherwise the whole thing would be too...

Simple BL Touch mount for Ender 3 V2, using 2 pcs M3 Screw STL parts are pre-oriented for easy print and good results Additional parts needed : M3x6 Button Head/ Hex Screw 4 Pcs M3 Nut 2 Pcs Probe offset for the firmware: X-42,Y-5 Original Creality...

Solid feet for the Ender 3 v2, problably other Enders/printers as well, fits all 40x40 profiles. 43mm high, 20mm wide, (20x20mm wide at the bottom). I made these to make room for larger PSU and Motherboard fans. Remove the orignal rubber feet...

A screen cover for the Ender 3 V2. To keep the dust off it when not in use. Because I use OctoPrint, I rarely need to see the screen and my work area is quite dusty. Has a knob for easy removal, and has the Ender logo I have included the FreeCAD...

A screen cover for the Ender 3 V2. To keep the dust off it when not in use. Because I use OctoPrint, I rarely need to see the screen and my work area is quite dusty. Has a knob for easy removal, and has the Ender logo I have included the FreeCAD...

Este es una adaptacion de este modelo https://www.thingiverse.com/thing:5260591Los eslabones no son mios, El credito de los eslabones es unica y exlusivamente de https://www.thingiverse.com/arek_r1/designsLo unico que hice fueron unos pequeños...

mod for original spool holder and my feet 35mm 35 mm feet feet: https://www.thingiverse.com/thing:4699997 bottom mainboard for noctua 40x40x10 with 2 stepdown lm 2596 https://www.thingiverse.com/thing:4684550 fan 60x60x25 noctua fan grid...

I did found one similar model, but it was way to small - couldn't push them on extrusion and rubber feet didn't fit also - so I amde my own :)  For ender 3 v2 users: remove PSU (black) cover, the PSU will become cooler and then the feets...

I need to clean my printer I know lol. ...This is a Knob for the Ender 3 V2 Extruder. The size is perfectly measured to tightly fit over the extruder knob slot. ...If you have any issues please let me know, I will try to help!

Designed up this Ender 3 V2 LCD Support to move it closer to the body and save space on printer place. ... Printing: Print it in horisontal with supports (minor needed) with 50 degrees touch base only PLA (20% infill) 210º Extruder 60º Base ...

... the way, so I made this. ...It is mountable on the Ender 3 V2, and I'm not sure about the pro. Definitely not the original, though. It is made for the raspberry pi 4b. ...Thanks to https://www.thingiverse.com/thing:4665097/ for making this originally!

This is a divider that will fit in the larger section of the drawer under the bed of a Creality Ender 3 v2. Each segment has it's appropriate size etched into the bottom. ... I bought this kit on amazon:...

... downloaded and printed another of a similar type but it basically served no purpose due to its small size. My design fits perfectly on my Ender 3 V2. I hope you guys like it. If you download it, hit me with some feedback on it! ...Thanks.

Turns out in the upgrade to the Ender 3 v2, they used a new part for the beeper which is a lot smaller than the original. So I replicated the design with the new sizes. ... The upper section cannot be any thicker (which would increase the sound...

After making Ender 3 v2 ikea lack, I wanted to take the motherboard out and made a simple drawing compatible with the motherboard in Fusion 360. I used a fan size of 80x80mm in a drawing. ...cover screw holes were created for 3mm bolts.

Filament Arm for Ender 3 V2: -will keep your filament away from the leadscrew -no support needed -no bed adhesion needed -10% infill is enough -friction fit (dimensional accuracy differs per print/printer, i am not to blame if it doesn't fit well)

Turns out in the upgrade to the Ender 3 v2, they used a new part for the beeper which is a lot smaller than the original. So I replicated the design with the new sizes. ... The upper section cannot be any thicker (which would increase the sound...

I wanted a filament guide that could fit over the filament holder on my Ender 3 V2. This is something I put together on TinkerCad quickly to do that. ... If you want to tweak it or play with it then you can find the original over on...

Tool holder for Ender 3 v2. Slides onto the upper rail. Holds a pair of wire cutters on the end, plus tweezers, a wide spudger, 2 SD cards, 2 microSD cards and USB stick. ...I would recommend printing with support for the wire cutter holder

This is a 53.5 mm diameter dial gauge holder for the Ender 3 V2 printer. It sits on top of the extruder fan housing and attaches to the extruder with an M8 x 25 mm screw. The bracket is of the clamp type. ...For the comparator there is a M6 x 60 mm or...